Conventional Radio Systems

Two-Way Radio Concepts and Electronics Fundamentals · Last updated · About 5 min read

Overview

Conventional radio systems introduce a repeater into the signal path to extend coverage well beyond what direct radio-to-radio (simplex) communication can achieve. A repeater receives a radio's transmission and immediately re-transmits it at higher power and/or from a more advantageous location (e.g., a tower, rooftop, or hilltop), allowing radios that could never hear each other directly to communicate.

In a conventional system, users manually select from a set of pre-programmed channels — each channel typically corresponds to a specific repeater or frequency pair — and get instant access to that channel with no call setup delay. This is in contrast to Trunked Radio Systems, where a control station dynamically assigns frequencies from a shared pool.

TX/RX Frequency Offset

All repeater-based systems transmit and receive on two different frequencies (a "frequency pair"), so the repeater can receive a radio's uplink and simultaneously retransmit it as a downlink without interference. The gap between these two frequencies is called the offset:

  • UHF: typically around a 5 MHz offset.
  • VHF: the offset can be smaller or larger than the UHF-typical figure, depending on the band plan and regulatory allocation.

Analog Conventional

Any analog, dealer-programmable two-way radio (excluding consumer FRS radios, which are not user-programmable) can be set up on an analog conventional system. The radio is simply programmed with the repeater's input/output frequency pair and any associated privacy tone (CTCSS/DPL).

Digital Conventional

Any digital radio can be programmed for digital conventional operation in the same way — programmed with the repeater's frequency pair — but the radio and repeater must share a common digital protocol, such as DMR (Motorola) or NXDN (Icom/Kenwood). Digital conventional systems can add features like two-slot TDMA capacity gains, integrated encryption, and data services on top of the same repeater infrastructure used for analog.

Channel and Repeater Assignment in Practice

Setting up a conventional system involves more than picking a frequency pair. A radio tech or system integrator typically works through several coordination steps:

  • Frequency/site planning: the frequency pair (or pairs, for multi-channel sites) must be selected to avoid interference with neighboring repeaters and to comply with FCC or other regulatory band-planning rules. Site engineers also plan antenna height, power, and coverage footprint before assigning channels to users.
  • Channel assignment to talkgroups/departments: once frequency and tone are locked in, the radio tech programs each department, shift, or talkgroup into a specific channel slot in the radio's codeplug — e.g., Channel 1 = Fire Dispatch, Channel 2 = Public Works, Channel 3 = Security. Dispatchers then simply select the channel corresponding to the group they need to reach, since access is instantaneous with no call setup delay.

Scanning Multiple Channels

Radios programmed with more than one conventional channel can scan a defined list of channels rather than sit on just one:

  • Priority scan lets one or two channels be flagged as higher priority so the radio checks them more frequently during a scan cycle, reducing the chance of missing important traffic on a critical channel even while scanning several others (Intercoms Online: 2-Way Radio Priority Channel Scan; Aircomm: Priority Scan).
  • Talkback (sometimes called scan-transmit-dwell) lets the user key up and reply directly on whatever channel the scan most recently stopped on, without having to manually switch the channel selector to match — useful when a scanning radio lands on a channel with an incoming call and the user needs to respond quickly (Intercoms Online: 2-Way Radio Priority Channel Scan).

Conventional vs. Trunked: Capacity, Cost, and When Each Makes Sense

Conventional systems are simpler and generally cheaper, but that simplicity puts a ceiling on how many users a given number of channels can practically support:

Factor Conventional Trunked
Typical capacity Roughly 70 users per channel is a commonly cited rule of thumb, with total capacity scaling directly (and only) with the number of channels available Capacity scales more efficiently because a shared pool of channels/frequencies is dynamically allocated on demand, since not every user needs a channel at the same instant
Control channel overhead None — every programmed channel is available for user traffic At least one channel per site is dedicated to trunking control (assigning calls to voice channels) rather than carrying voice itself
Call setup Instant — user just presses the button on a pre-selected channel Brief delay while the controller assigns an available voice channel
Relative radio/system cost Lower; typically simpler infrastructure Radios and controllers commonly cost on the order of 2–3x more than conventional equivalents, though large systems can partly offset this by needing fewer total licensed channels
Good fit Roughly 3 or fewer independent user groups of about 70 or fewer users each, where groups don't need to talk to each other and instant access matters most; smaller/rural deployments Sites needing 4 or more channels, large or diverse user populations, or frequent cross-group/cross-department communication

(Figures per Tait Communications: Trunked vs Conventional Radio Networks.)

In practice, many organizations start with conventional systems because of the lower cost and simplicity, then migrate to (or add) Trunked Radio Systems as user counts, channel needs, or cross-department coordination requirements grow. Some deployments — including P25 systems — mix trunked and conventional elements in the same network, using conventional channels for interoperability or backup while the bulk of routine traffic rides on trunked talkgroups.

Beyond a Single Repeater

A single conventional repeater serves one site. When coverage needs to span multiple sites or buildings, Motorola's IP Site Connect technology links multiple repeaters together over an IP network so they behave as one unified conventional system across sites.

For systems that need dynamic, on-demand allocation of channels across a large user base rather than fixed user-selected channels, see Trunked Radio Systems.

References

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.