RadioPro IP Gateway Overview: Radio-over-IP Interface for Control-Station Radios

RadioPro and CTI Products · Last updated · About 8 min read

What the RadioPro IP Gateway does, how a RadioPro system is architected, its client limits, licensing, indicators, environment, power and bandwidth needs.

The RadioPro IP Gateway is the hardware that makes a two-way radio reachable over an IP network. It connects a control-station radio to a LAN or WAN, translates between the radio and IP, and acts as the server for the clients that connect to that radio. The data sheet calls RadioPro a Radio-over-IP (RoIP) and Dispatch-over-IP (DoIP) solution for systems such as Motorola MOTOTRBO and Kenwood NEXEDGE, reachable from Windows PCs and from iOS and Android devices. For general RoIP background see roip-radio-over-ip and control-stations.

Architecture

  • One gateway per control-station radio. Each radio used for voice needs its own IP Gateway, and one radio is needed for each channel or talk group that must be used at the same time. The gateway is the network interface for its radio.
  • The gateway is the server. Clients (Dispatch, Solo and Talk) connect to the gateway. There is no server PC, which reduces single-point-of-failure concern.
  • Distributed or central. Gateways, radios and clients can be in one place or scattered across sites connected by a LAN, a WAN such as the Internet, or a VPN (networking-vpns).
  • Mixed clients. A system can combine Dispatch, Solo and Talk clients. A Dispatch client is multi-link (it connects to many gateways at once); Solo and Talk are single-link (one gateway for a session).
  • Tested limits: up to 80 clients per IP Gateway and up to 70 IP Gateways per Dispatch client.

A functional system needs at least one gateway, one client, Ethernet access to a LAN or WAN, and a connection license for each client that needs one.

What the data sheet specifies

Item Value
Part number S2-61815 (kit, includes the power supply); see radiopro-part-numbers-and-ordering
Radio platforms Analog, digital conventional, trunked and DMR
Control-station radios See radiopro-supported-control-station-radios
Dimensions and weight 8.25 in wide x 2.5 in high x 11.5 in deep; 3 lbs
Temperature and humidity 0 to 50 degrees C, 10 to 95% non-condensing
Power 11.5 to 12.5 VDC input, 2 A maximum, supplied from the included AC adapter (100 to 240 VAC, 200 mA maximum, 50 to 60 Hz). The gateway needs its own power feed; Power over Ethernet is not supported
USB ports (rear) 4: enough for one MOTOTRBO voice radio and three data revert radios without a hub (radiopro-data-revert-radios)
Log retention 30 days, retrieved with the ICU utility
Tx/Rx impedance (MOTOTRBO) 600 ohms
Tx/Rx impedance (Kenwood) Auto
Maximum clients 80 (Solo, Talk for Mobile or Dispatch clients)
Network bandwidth 2.2 kBytes/s per connected client with audio compression; 22 kBytes/s without
Port TCP 48222 by default (configurable)
Power-on momentary press of the Power button

The kit includes a power supply, a USB flash drive with the RadioPro software, installation guides and licenses, and a Cat 5 patch cable. The radio interface cable for the specific control-station radio is a separate item. The gateway can be rack-mounted on a shelf of at least 12 inches depth, with the control-station radio beside it.

Licensing

  • Dispatch clients each need a unique license key file that sets the number of gateways the console can connect to and which options (GPS, Text and others) are available. Features and gateway connections can be added to a license at any time; components can be added but not removed. See radiopro-dispatch-layout-gateways-and-licensing.
  • Solo and Talk clients are licensed on the gateway. The license value, from 1 to 80, is the number of simultaneous persistent Solo and Talk users the gateway will maintain. The serial-number label on the bottom of the gateway shows the quantity installed at the factory, but the ICU utility should always be used to confirm the current number.
  • A gateway may ship with a timed license of 120 days; after that a gateway will not stay connected to a client for longer than five minutes until the license is converted to a non-expiring one by exchanging a license file with CTI Products. See radiopro-ip-gateway-installation-and-configuration.

Version compatibility

A Dispatch or Solo client and an IP Gateway are compatible when the first two digits of their versions match; the third digit is a minor revision. The compatibility table in the installation guide shows that Dispatch version 9 works only with version 9 gateways and Dispatch version 8 only with version 8 gateways, while the Solo client and the Talk mobile app work with both version 8 and version 9 gateways. When upgrading both clients and gateways, it is usually better to upgrade the gateways first. See radiopro-system-upgrades.

Operation and indicators

  • A watchdog circuit monitors the gateway program. If it detects a fault it re-initializes the gateway, which can take up to two minutes, during which clients have no connection to the radio.
  • The blue LED on the Power button at the front shows the gateway is powered.
  • A red LED, visible through the vents on the left side, shows the watchdog state: slow blinking (1 second on, 1 off) means rebooting, normally for up to two minutes after power-up; steady means hardware and software are operating correctly; fast blinking means the watchdog has found a problem and a reboot will start within 5 seconds.
  • The Power button gives a soft shutdown with a momentary press, or a hard shutdown if held for up to 5 seconds.

Client capacity

The "80 clients" figure applies to any mix of Dispatch, Solo and Talk clients. Because the gateway passes all audio to all connected clients, it is guidance based on processor load and network use, not a hard ceiling: more than 80 clients can attach, and noticeable performance degradation typically begins somewhere around 100 to 120 clients.

The radio side

  • One radio, one channel. A gateway attaches to exactly one voice control-station radio, and every connected client follows that radio's currently selected channel. Clients cannot listen to different channels through one gateway at the same time, and when one client steers the radio to another channel, every client on that gateway hears the change. Simultaneous, independent access to several channels needs several gateways, each with its own radio.
  • Connection methods. A Motorola MOTOTRBO radio connects by a short USB cable to the rear connector (a virtual Ethernet link over USB), with a single voice interface per gateway. A Kenwood NEXEDGE radio connects by a serial cable with a custom 9-pin connector on the gateway. Both brands give the gateway the same capabilities: voice, push-to-talk, channel steering, GPS and text messaging, as the radio system allows (radiopro-dispatch-feature-availability-by-system-type). Data revert radios use separate connectors (radiopro-data-revert-radios).
  • If the radio disconnects. If the radio is powered off or its cable is unplugged, all connected clients show that the gateway has lost its connection to the radio. When the radio is powered back on or reconnected, the gateway normally reconnects by itself without a reboot, and it logs MOTOTRBO and NEXEDGE radio disconnects.
  • Generic COR/PTT radios. On an installation that uses plain COR/PTT lines, such as the APX 4500 (radiopro-ip-gateway-with-motorola-apx-4500) or any generic Rx/Tx radio, the gateway has no way to know the radio has lost power or been disconnected, because those lines carry only contact closures and audio. A dead radio on such an interface produces no client indication and no log entry; it simply goes silent, so the radio itself must be checked.
  • Power loss. The gateway restarts automatically when power is restored. A UPS is needed only when operation must continue through an outage, and then the network equipment and the control-station radio need backup power as well.

Firmware updates

A gateway's firmware can be upgraded within a major version as long as the first two digits of the firmware version match, for example from one 9.3.x release to another. Downgrading is discouraged: CTI tests the upgrade path thoroughly, but downgrades are not part of the standard tests. The update is applied through the ICU utility (General tab, Upgrade Firmware; installation typically takes 15 to 45 seconds), through the Dispatch client, or from a USB flash drive whose firmware file name begins with RadioPro_Gateway (radiopro-system-upgrades). The gateway renames a file it has installed by appending "installed" and does not reinstall a file whose name contains that word, so a drive can safely be left in place. The upgrade methods that CTI describes as "remote access" work across a WAN as long as the gateway is reachable from the upgrading PC; ICU's automatic discovery is a broadcast that does not cross a router, so in that case the gateway's IP address is typed in.

Application ports

Clients reach the gateway on a single TCP port, 48222 by default, which can be changed in ICU. The gateway also uses well-known UDP ports for MOTOTRBO data services: 4005 for ARS, 4007 for text messaging and 4001 for the location (GPS) server, plus UDP 123 for NTP time synchronization. A firewall between clients and the gateway must at least allow the client port (port-forwarding-and-remote-access).

Installation environment

Do not install the gateway where there is extreme temperature or humidity, high EMI or RFI, heavy dust, high ESD or extreme vibration. To prevent RF interference keep mobile radio antennas at least 24 feet away in high-power mode (12 feet in low-power mode) and portable radios at least 6 feet away. Lightning protection should be applied at the equipment and at the building entry point; circuit breakers and fuses are the best protection against extended over-current and over-voltage.

Battery backup note: the gateway power input accepts only 11.5 to 12.5 volts, so it will not run directly from the typical 13.8 VDC battery-backup charging voltage.

Source documents

This article summarizes the following published CTI Products manuals. They are the authoritative reference.

See also: CTI product documentation

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.