Two-Way Radio Knowledge Base
Technical articles on two-way radio systems, radio over IP, dispatch, push-to-talk, MOTOTRBO, NEXEDGE, P25, networking, RF engineering and CTI's RadioPro and MCN products. 170 articles in 7 categories.
Browse by category
- Two-Way Radio Concepts and Electronics Fundamentals (61)
How land mobile radio systems work: signaling, trunking, licensing, dispatch, radio over IP and glossaries, with the electronics basics behind them (such as decibels) and troubleshooting references. - Motorola MOTOTRBO and P25 Systems (31)
MOTOTRBO (DMR), APX and P25 radios, Capacity Plus and IP Site Connect, radio management, and Motorola infrastructure explained. - Kenwood NEXEDGE and NXDN (9)
Kenwood NEXEDGE radios, repeaters, trunking and the NXDN digital standard. - RF, Antennas and Radio Sites (3)
Propagation, antennas, duplexers, test equipment, site power, towers and the practical engineering of two-way radio sites. - Networking for Radio Systems (28)
IP addressing, VLANs, NAT, VPNs, QoS for push-to-talk, time sync and the tools used to troubleshoot radio-over-IP networks. - RadioPro Product Documentation (28)
Guides to RadioPro Dispatch, Solo, Talk and the IP Gateway: setup, operation, planning and upgrades, summarized from CTI's published manuals. - MCN and BRSC Comparator Monitoring (10)
CTI's Monitoring and Control Network for voting-receiver comparators, MCN software, hardware modules, TSAM transmitter steering and BRSC, summarized from CTI's published manuals.
Two-Way Radio Concepts and Electronics Fundamentals
- Analog vs Digital RadioTwo-way radios come in two fundamental flavors — analog and digital — and understanding the tradeoffs between them is the foundation for almost every other.
- Anatomy of a Two-Way Radio SystemThe levels of a two-way radio system, from simplex radio-to-radio through repeaters to networked, dispatched systems, and how much system you need.
- Audio Clipping: What It Is, What It Sounds Like and How to Fix ItAudio clipping explained with a computed waveform and harmonic-distortion chart: what causes harsh, distorted radio audio, how to find the stage that clips, and how to set levels.
- Audio Levels and Radio InterfacingWhenever a two-way radio is wired to external equipment — a Radio over IP (RoIP) gateway, a dispatch console, a logging recorder.
- Base Station vs. Mobile vs. Portable Radio ClassesPower output, antenna size/gain, and available battery/duty-cycle all differ substantially across the three classes.
- Busy Queuing in Trunked SystemsA trunked radio system has more talkgroups than voice channels by design — statistical sharing is the whole point.
- Channel Scan and Priority ScanScanning lets a two-way radio monitor multiple channels with one receiver: the radio rapidly steps through a programmed list of channels.
- Common Radio Programming ParametersEvery brand's programming software — Motorola MOTOTRBO CPS, Kenwood NEXEDGE programming software.
- Control StationsA control station is a mobile radio — a radio designed for vehicle installation — that is instead installed permanently at a fixed location.
- Conventional Radio SystemsConventional radio systems introduce a repeater into the signal path to extend coverage well beyond what direct radio-to-radio (simplex) communication can achieve.
- COR and PTT InterfacingAlongside these two logic signals, a basic interface also carries plain analog Tx/Rx audio — the receive audio coming out of the radio.
- Cross-Band RepeatCross-band repeat is a repeater configuration that receives on one frequency band and retransmits on a different band — for example.
- Cross-Patching and System BridgingOrganizations routinely need radios on one system to talk to radios on another: a VHF (Very High Frequency) analog fleet to a UHF.
- Designing a Two-Way Radio SystemThe decision sequence for designing (or evaluating) a professional two-way radio system, with links to the detail pages each decision depends on.
- Digital Access Codes: Color Code, RAN, and NACOn analog FM channels, CTCSS (Continuous Tone-Coded Squelch System, Motorola's "PL" or Private Line) adds a continuous sub-audible tone to a transmission.
- Digital Radio Audio ArtifactsEverything on this page follows from that: the vocoder is superb at one talker's speech and structurally bad at everything that isn't speech .
- Dispatch Console Operations ConceptsAlongside select-and-talk, consoles offer per-channel instant transmit buttons that key a specific channel regardless of selection — fast.
- Dispatch Mapping Systems and Slippy MapsGPS coordinates themselves are conventionally expressed in WGS84 (World Geodetic System 1984).
- DMR Digital Mobile RadioDMR (Digital Mobile Radio) is a digital radio standard created by ETSI (the European Telecommunications Standards Institute).
- Electronics Fundamentals: Decibels (dB, dBm, dBi)The decibel expresses ratios logarithmically, turning gains and losses along a signal path into simple addition: the core definitions for radio link budgets.
- Emergency / Man-Down AlertsMan-down and lone-worker alert features use sensors built into a portable radio to automatically detect a possible medical emergency or fall.
- Failsoft ModeFailsoft is the fallback condition a trunked radio system enters when it loses the ability to trunk normally — most commonly triggered by a loss of the.
- GPS (Global Positioning System)GPS is best known for positioning, but land mobile radio infrastructure relies just as heavily on the precise timing signal GPS satellites broadcast.
- Interoperability and Mutual-Aid ChannelsInteroperability in public-safety radio means responders from different agencies — often on different systems, bands.
- IP Site ConnectIP Site Connect is a Motorola MOTOTRBO technology that links multiple digital repeaters together over a standard IP network (the internet or a private WAN).
- LMR Land Mobile RadioLand Mobile Radio (LMR) is a category of two-way radio system built for higher quality, more capability.
- Mobile Radio InstallationBest practices for installing a mobile two-way radio in a vehicle — and, by extension, for fixed control station installs, which reuse mobile hardware.
- Network Troubleshooting CommandsA field reference for the built-in Windows commands used constantly in radio-system network troubleshooting (dispatch PCs, gateways, site LANs).
- PL Tones, CTCSS, and DCS"PL" stands for Private Line , Motorola's trademarked name for the technology more generically known as CTCSS .
- Pre-Emphasis and De-EmphasisPre-emphasis boosts high audio frequencies in an FM transmitter before modulation, and de-emphasis restores them in the receiver to reduce noise.
- Push-to-Talk over Cellular (PoC)PoC delivers a walkie-talkie-style push-to-talk experience over LTE/5G cellular networks (or Wi-Fi) rather than over dedicated LMR frequencies.
- Radio Cloning / Clone ProgrammingBoth accomplish the same basic goal — replicate a known-good configuration onto another radio quickly — but they differ substantially in capability and where.
- Radio Concepts for IT ProfessionalsA professional radio system is a real-time, half-duplex, broadcast voice network with extremely constrained bandwidth.
- Radio Firmware UpdatesUpdating firmware changes what the radio can do ; updating the codeplug changes what it is set up to do .
- Radio Frequency BasicsUnderstanding how two-way radios work starts with a few core concepts: frequency, Hertz, and wavelength.
- Radio IDs and Digital AddressingDigital two-way radio standards give every radio a numeric identity and address calls to numeric group and individual IDs.
- Radio Management GlossaryA glossary of terms used in Motorola radio programming and fleet management, including CPS, OTAP, ASK and POP25.
- Radio Management Licensing and SecurityThis page summarizes licensing, access control, certificates, encryption-related boundaries, network exposure.
- Radio Management OverviewMotorola uses several products with overlapping terms such as CPS , Radio Management , OTAP , POP25 , and RadioCentral .
- Radio Management TroubleshootingThis page provides a cross-product troubleshooting method for MOTOTRBO Radio Management, APX Radio Management, MOTOTRBO OTAP, APX POP25, and RadioCentral.
- Radio Programming Methods ComparisonUse this page to select the correct programming method and avoid mixing MOTOTRBO and APX terminology.
- Radio System and Phone System IntegrationTwo-way radio systems and telephone systems solve different communication problems — a radio system provides instant.
- Radio Terminology GlossaryADC / DAC (Analog-to-Digital / Digital-to-Analog Converter) The circuits that turn real-world analog signals into digital samples and back.
- Reverse Burst and Squelch Tail Elimination (STE)Reverse burst (Motorola's term; generically squelch tail elimination, STE ) is an end-of-transmission signaling trick in analog FM radio: just before.
- RoIP (Radio over IP)Radio over IP (RoIP) is the general term for carrying two-way radio voice and control traffic over an IP network (Ethernet, the internet, cellular.
- RSSI (Received Signal Strength Indicator)A detail that catches people off guard: in the original IEEE 802.11 (Wi-Fi) specification, RSSI is explicitly defined as an arbitrary.
- Satellite Communications: StarlinkStarlink is a broadband satellite service operated by SpaceX: what it offers and how it fits two-way radio and radio-over-IP connectivity.
- Serial (RS-232) and USB Programming InterfacesThe remaining pins carry hardware handshaking signals (RTS/CTS — Request To Send/Clear To Send.
- Simplex Radio SystemsSimplex is the most basic two-way radio system architecture: radios communicate directly with one another, radio-to-radio, on a single shared channel.
- Squelch TypesHow squelch mutes a receiver when no wanted signal is present, and the carrier, tone-coded and digital squelch types used in two-way radio.
- Talkaround and Direct ModeThe distinction is mostly one of frequency plan: pure direct/simplex uses a dedicated simplex frequency.
- Talkgroups and Fleet MappingA talkgroup is a virtual channel: a logical grouping of radio users who hear each other's transmissions.
- TDMA vs FDMATDMA (Time Division Multiple Access) and FDMA (Frequency Division Multiple Access) are the two competing approaches used by modern digital two-way radio.
- Troubleshooting RoIP and Gateway ConnectivityWhen a system works, record it: IP addresses and masks, firewall rules, port forwards, versions of every component, audio level settings.
- Troubleshooting Two-Way RadiosThis page is a systematic, vendor-neutral method for troubleshooting individual two-way radios and radio-to-radio communication problems.
- Trunked Radio SystemsTrunked radio systems take the repeater concept from Conventional Radio Systems a step further.
- Trunking Registration and AffiliationA radio re-affiliates when the user changes talkgroups, and re-registers when it roams between sites — so the controller's picture of "who is where.
- Two-Tone Paging and Quik-CallTwo-tone sequential paging is a decades-old analog signaling method used to selectively alert pagers, station receivers.
- Two-Way Radio Dispatch and Computer-Aided Dispatch (CAD)Modern IP-based dispatch consoles are built with extensible architectures specifically so they can integrate bidirectionally with other software rather than.
- UHF RadiosUHF (Ultra High Frequency) two-way radios operate in the 400–512 MHz range and are the most popular band for commercial and business two-way radio use.
- VHF RadiosVHF (Very High Frequency) two-way radios operate across the broader 30–300 MHz VHF spectrum.
Motorola MOTOTRBO and P25 Systems
- APX POP25 Over-the-Air ProgrammingPOP25 , or Programming over Project 25 , is Motorola's method for remotely reading or writing supported APX radio configuration through an ASTRO 25 data path.
- APX Radio ManagementAPX Radio Management , commonly called APX RM , extends ASTRO 25 CPS with a centralized fleet database, templates, scheduled programming jobs, job history.
- ARS (Automatic Registration Service)Automatic Registration Service (ARS) — often also called the "Presence Notifier" function — is a MOTOTRBO feature that lets a radio report its online/offline.
- CodePlugA codeplug is the complete configuration file loaded into a two-way radio (or repeater) that defines everything about how it operates: which frequencies it.
- IMPRES Battery/Charging SystemIMPRES is Motorola's intelligent, automated battery management ecosystem — IMPRES batteries paired with IMPRES chargers — designed to extend battery life and.
- Motorola APX 4500This mixed-mode support lets an agency operate on modern P25 trunked systems while remaining compatible with legacy analog infrastructure during a transition period.
- Motorola APX Portable and Mobile Radios (6000/7000/8000/NEXT Series)This page covers Motorola's mainstream APX portable (handheld) and mobile (vehicle-mounted) radio lines beyond the single specific model already documented.
- Motorola CCGW (Conventional Channel Gateway)This page is a dedicated deep dive on the CCGW, already referenced on ASTRO 25 Console Gateways, ASTRO 25 Border Routers, ASTRO 25 Core Routers.
- Motorola MOTOTRBO Network PortsThis page enumerates the standard TCP and UDP ports used on an IP-networked MOTOTRBO system — repeaters, control stations, MNIS Gateways.
- Motorola MOTOTRBO OverviewMOTOTRBO is Motorola Solutions' professional line of digital two-way radios, built on the DMR (Digital Mobile Radio) standard.
- Motorola MOTOTRBO Portable RadiosThis page covers MOTOTRBO's handheld (portable) product families, complementing the mobile/vehicle-mount models already documented individually.
- Motorola MOTOTRBO XPR 2500The XPR 2500 supports both analog and digital ( DMR ) operation, allowing an organization to continue using its existing analog infrastructure while.
- Motorola MOTOTRBO XPR 4550The Motorola MOTOTRBO XPR 4550 mobile radio is built on the ETSI DMR Tier 2 digital standard: features and how it is used in MOTOTRBO systems.
- Motorola MOTOTRBO XPR 5550The XPR 5550 supports both digital ( DMR ) and analog operation, and can migrate at the customer's own pace: analog and digital modes can run concurrently on.
- Motorola MOTOTRBO XPR 5550eThe XPR 5550e is a mobile (vehicle-mounted) digital two-way radio in Motorola's MOTOTRBO lineup.
- Motorola Radio Programming and Fleet ManagementA guide to Motorola radio management topics that keeps MOTOTRBO/DMR and APX/P25 products separate, with where to start for CPS, OTAP and programming.
- Motorola Tone Remote ControlMotorola-specific implementations of EIA Tone Remote Control (TRC) — the console-to-base-station signaling scheme covered generally on that page.
- MOTOTRBO Capacity MaxMOTOTRBO Capacity Max is Motorola's largest-scale DMR trunking architecture: how it works, what it adds beyond Capacity Plus and when it fits.
- MOTOTRBO Capacity Max System ServerThis page is a deeper technical dive on the Capacity Max System Server (CMSS) specifically.
- MOTOTRBO Capacity PlusMOTOTRBO Capacity Plus is Motorola's entry-level DMR trunking system: how a single site shares a pool of channels, and when to choose it.
- MOTOTRBO Data ServicesMotorola MOTOTRBO is a digital radio platform built on the DMR (Digital Mobile Radio) standard — see DMR.
- MOTOTRBO Linked Capacity PlusLinked Capacity Plus is the multi-site variant of MOTOTRBO Capacity Plus, linking trunked sites into one wide-area DMR system.
- MOTOTRBO Radio ManagementMOTOTRBO Radio Management 2.0 , commonly shortened to RM , extends MOTOTRBO CPS 2.0 with a centralized database, reusable templates, fleet records.
- MOTOTRBO Repeaters (SLR Series)Feature licenses purchased and installed on the repeater determine which of these modes it may run.
- MOTOTRBO Restricted Access to System (RAS)Restricted Access to System (RAS) is a Motorola MOTOTRBO repeater-authentication feature that prevents unauthorized radios from using a repeater system.
- MOTOTRBO RM Architecture and DeploymentThis page focuses on planning and operating the computers, services, database, and network paths used by MOTOTRBO Radio Management.
- MOTOTRBO RoamingIn a multi-site Motorola MOTOTRBO system, roaming is the subscriber radio's ability to automatically move from one repeater site to another as the user.
- P25 DFSI (Digital Fixed Station Interface)The Digital Fixed Station Interface (DFSI) is one of the open, standardized interfaces in the Project 25 (P25) digital radio standard suite (see P25 Project 25 ).
- P25 Project 25Project 25 (P25, also called APCO-25) is a suite of digital radio standards designed primarily for North American public-safety use.
- Programming Motorola MOTOTRBO RadiosMotorola's MOTOTRBO (DMR) radios and repeaters — see Motorola MOTOTRBO Overview — are configured using Customer Programming Software (CPS).
- Programming Motorola P25 RadiosMotorola's P25 subscriber radios (the APX line — see Motorola APX 4500 ) were historically programmed with Radio Service Software (RSS).
Kenwood NEXEDGE and NXDN
- Kenwood NEXEDGE NX 3720 3820The NX-3720 (VHF) and NX-3820 (UHF) are mobile radios in Kenwood's NX-3000 series , part of the NEXEDGE family.
- Kenwood NEXEDGE NX 5700 5800The NX-5700 (VHF) and NX-5800 (UHF) are mobile radios in Kenwood's NX-5000 series , the newer, top-tier generation of the NEXEDGE family.
- Kenwood NEXEDGE NX 700 800Fleet and land-mobile users needing mixed analog/digital operation during a transition to NXDN digital.
- Kenwood NEXEDGE NX 720 820The NX-720 (VHF) and NX-820 (UHF) are Kenwood NEXEDGE mobile radios that followed the earlier NX-700/NX-800 generation.
- Kenwood NEXEDGE OverviewNEXEDGE is Kenwood's (now JVCKENWOOD) line of digital two-way radios, developed by Kenwood in 2008 based on NXDN — an advanced.
- Kenwood NXR RepeatersKenwood's NEXEDGE infrastructure line carries the NXR model prefix: repeaters and base stations that anchor NXDN digital systems.
- NEXEDGE Trunking: Type-C and Type-DKenwood NEXEDGE systems built on the NXDN digital standard (see NXDN Digital Standard and Kenwood NEXEDGE Overview ) can operate as trunked radio systems.
- NXDN Digital StandardNXDN (Next Generation Digital Narrowband) is a digital radio standard developed jointly by Icom and JVCKENWOOD (Kenwood).
- Programming Kenwood NEXEDGE RadiosKenwood NEXEDGE radios (see Kenwood NEXEDGE Overview ) are configured using model-family-specific KPG-series programming software.
RF, Antennas and Radio Sites
- Repeater ControllersWhat a repeater controller does: keying logic, hang time, timeout timers and the other functions that run a repeater.
- Repeaters and Antennas BasicsThis page covers the fundamentals of how repeaters extend the range of two-way radio systems.
- SimulcastSimulcast ("simultaneous broadcast") is a technique where two or more repeater sites transmit on the exact same frequency, with the exact same modulation.
Networking for Radio Systems
- ACL (Access Control List)An access control list (ACL) is a list of rules configured on a router, switch, or firewall that specifies which traffic is permitted or denied.
- Computers Showing Different Times: Fixing Time Synchronization with NTPWhy computers, gateways and network devices drift apart on the clock, what breaks when they do, and how to set up and check NTP time synchronization on Windows, Linux and radio systems.
- DHCP vs. Static IP Addressing: Which to Use and WhyThe difference between DHCP and static IP addressing, how each works, when to use which for radio gateways, dispatch PCs and servers, and the mistakes that cause duplicate-address outages.
- End Point Protection on Radio and Dispatch ComputersWhat endpoint protection (antivirus, EDR, host firewall) is, why radio and dispatch PCs need it, and how to keep it from breaking installs, audio or network connections.
- Firewall Types: Stateful vs. StatelessA stateless firewall filters each packet in isolation, purely based on the information in that packet's own header (source/destination IP, port.
- IANA (Internet Assigned Numbers Authority)IANA is the organization responsible for globally coordinating the internet's foundational numbering and naming systems.
- IP Networking in Two-Way Radio SystemsModern land mobile radio (LMR) systems increasingly depend on IP (Internet Protocol) networks for far more than just an optional add-on feature.
- Latency, Jitter, and Packet Loss in Voice NetworksThree network impairments determine whether live voice over IP — telephony VoIP (Voice over IP) or radio RoIP (Radio over IP) — sounds good, tolerable.
- NAT (Network Address Translation)Network Address Translation (NAT) is a router function that rewrites the source and/or destination IP addresses.
- Networking: ARP (Address Resolution Protocol)ARP answers one small but essential question on an IPv4 network: "Who has this IP address.
- Networking: DHCP (Dynamic Host Configuration Protocol)DHCP is a client-server protocol that automatically assigns IP addresses (and related configuration like subnet mask, default gateway.
- Networking: DNS (Domain Name System)DNS translates human-readable names (like a hostname or domain name) into the numeric IP addresses.
- Networking: ICMP and PingICMP (Internet Control Message Protocol) is IP's built-in signaling channel — not a data transport like TCP / UDP.
- Networking: IP Address Classes (A, B, C, D, and E)Before CIDR (Classless Inter-Domain Routing) replaced it in 1993, IPv4 addresses were divided into five fixed "classes," identified by the value of an.
- Networking: IPv4IPv4 (Internet Protocol version 4) is the addressing scheme most IP networks — including most radio system IP backhaul described in IP Networking in Two-Way.
- Networking: IPv6IPv4 's 32-bit address space tops out around 4.3 billion unique addresses, which is far too small for a world with billions of internet users plus tens of.
- Networking: MAC AddressesA MAC (Media Access Control) address is the hardware-level identifier burned into (or assigned to) every network interface — Ethernet port, Wi-Fi adapter.
- Networking: TCP (Transmission Control Protocol)TCP is a connection-oriented transport-layer protocol that guarantees reliable, ordered delivery of data between two devices.
- Networking: UDP (User Datagram Protocol)UDP is a connectionless transport-layer protocol, defined in RFC 768 : it sends data ("datagrams") to a destination with no handshake, no connection setup.
- Networking: Unicast, Broadcast, and MulticastUnicast is one sender to one specific receiver, addressed to that single device's own unique IP address — a direct.
- Networking: VLANA Virtual LAN (VLAN) is a way to logically segment a single piece of physical network switching infrastructure into multiple separate networks that behave as.
- Networking: VPNs (Virtual Private Networks)A VPN creates a secure, encrypted communication path over a public or otherwise untrusted network (most often the internet).
- NTP (Network Time Protocol)The Network Time Protocol (NTP) is a networking protocol used to synchronize the clocks of computers and network devices across an IP network to a common.
- Port Forwarding and Remote AccessMany sites have no static public IP — the ISP (Internet Service Provider) changes it occasionally.
- SNMPSNMP (Simple Network Management Protocol) is a standard, widely-deployed protocol for monitoring and managing devices on an IP network — routers, switches.
- Subnet Masks Explained: Dotted-Decimal and CIDR NotationWhat a subnet mask does and the two ways to write it, dotted-decimal (255.255.255.0) and CIDR slash notation (/24), with a conversion table, worked examples and common mask mistakes.
- Switches, Routers, and HubsThe layer distinction is the durable mental model: hubs are layer 1 (bits), switches layer 2 (frames/MACs), routers layer 3 (packets/IPs).
- Wireshark and Packet CapturePacket capture means recording the actual network traffic passing a point in the network, packet by packet, for inspection.
RadioPro Product Documentation
- Bridging Two Radio Systems with RadioPro: Patching a MOTOTRBO System to a NEXEDGE SystemHow to carry audio between two different two-way radio systems, such as Motorola MOTOTRBO and Kenwood NEXEDGE, by patching two RadioPro IP Gateways over IP.
- Connecting a RadioPro IP Gateway to a Motorola APX 4500 P25 Control StationHow the RadioPro IP Gateway connects to a Motorola APX 4500 through an intercom (COR/PTT) interface, with ICU settings and P25 feature limits.
- Connecting a RadioPro IP Gateway to a MOTOTRBO Control-Station RadioMOTOTRBO CPS settings, IP addressing rules, Enhanced GPS and Connect Plus setup for RadioPro control-station and subscriber radios.
- Connecting a RadioPro IP Gateway to Kenwood NEXEDGE Control-Station RadiosKenwood FPU settings for NEXEDGE control-station, data revert and subscriber radios (NX-700/800, 720/820, 3720/3820, 5700/5800) used with RadioPro.
- Control-Station Radios Supported by RadioPro: MOTOTRBO, APX 4500 and NEXEDGE ModelsWhich Motorola and Kenwood radios can serve as RadioPro control stations, what each provides, minimum firmware and the rules for sharing a gateway.
- Installing and Configuring a RadioPro IP Gateway with the ICU UtilityStep-by-step outline for configuring a RadioPro IP Gateway with ICU, assigning a static IP, setting time sync, client accounts and aliases, and port forwarding.
- Microphones, Headsets, Footswitches and PTT Accessories for RadioPro ConsolesThe desk microphones, headsets, footswitches, speakers and PCs that suit RadioPro Dispatch and Solo, and how USB PTT microphones are configured.
- Planning a RadioPro System for MOTOTRBO: Gateways, Data Revert, ARS and GPSHow many IP Gateways and control-station radios a RadioPro system needs on conventional, IP Site Connect and Capacity Plus MOTOTRBO systems.
- RadioPro Applications by IndustryHow CTI's Application Focus briefs describe RadioPro in construction, education, energy, healthcare, hospitality, manufacturing and petrochemical.
- RadioPro Data Revert Radios: Adding GPS and Data Capacity to a MOTOTRBO or NEXEDGE SystemHow a dedicated data revert radio behind a RadioPro IP Gateway carries GPS and ARS traffic, with radio counts, configuration rules, Enhanced GPS capacity and cable part numbers.
- RadioPro Dispatch Demo and Quick StartHow to install the RadioPro Dispatch demo client, connect it to CTI's demo radio system and set up audio and recording for a test drive.
- RadioPro Dispatch Feature Availability by MOTOTRBO and NEXEDGE System TypeWhich RadioPro Dispatch features (text, GPS, ARS, private call, remote monitor and more) work on each MOTOTRBO and NEXEDGE system type.
- RadioPro Dispatch GPS Mapping, Quick Map and Geo-fencesGPS tabs, the Quick Map, subscriber trail crumbs, place markers, nearest-radio lookup, geo-fence conditions and reports in RadioPro Dispatch.
- RadioPro Dispatch History Logging, Recent History and Archive ViewerHow RadioPro Dispatch logs voice and events, replays audio, diagnoses volume, and how to search and export records with the Archive Viewer.
- RadioPro Dispatch Installation, Layout, Gateway List and LicensingPC requirements, installation, license import, gateway list with failover, layouts, audio presets and settings for RadioPro Dispatch.
- RadioPro Dispatch Software OverviewWhat RadioPro Dispatch is: a Windows dispatch console for MOTOTRBO and NEXEDGE radio systems with voice, GPS mapping, text, telemetry and logging.
- RadioPro Dispatch Subscribers, Contacts, Text Messaging and Missed CallsThe Subscribers panel, alias contact table, subscriber actions such as Radio Check and Call Alert, text messaging and the Missed Calls panel in RadioPro Dispatch.
- RadioPro Dispatch Telemetry and Remote I/O (Tallysman Sprite and Advantech ADAM)How the RadioPro Dispatch Telemetry panel monitors and controls vehicle and facility I/O using radio-based Tallysman modules and IP-based Advantech ADAM modules.
- RadioPro Dispatch Voice Dispatching, Audio Levels and EmergenciesHow a RadioPro Dispatch operator makes and receives calls, sets Select/Unselect and microphone levels, patches talk groups and handles emergencies.
- RadioPro IP Gateway Overview: Radio-over-IP Interface for Control-Station RadiosWhat the RadioPro IP Gateway does, how a RadioPro system is architected, its client limits, licensing, indicators, environment, power and bandwidth needs.
- RadioPro IP Gateway RTP Streaming and Logging Recorder InterfacesTwo ways to record RadioPro radio traffic: analog audio to a logging recorder, or RTP packets with radio metadata sent to a recorder or incident-management system.
- RadioPro Link: Reach a RadioPro IP Gateway Over Starlink, Cellular and CGNATRadioPro Link gives a RadioPro IP Gateway a stable remote endpoint, so Dispatch, Solo, Talk and ICU can reach it over Starlink, cellular or CGNAT connections without a static public IP address or port forwarding.
- RadioPro Part Numbers and Ordering Guide: IP Gateway Kit, Cables, Licenses and Dispatch ModulesCTI part numbers for the RadioPro IP Gateway kit, radio interface and data revert cables, Solo and Talk license packs, Dispatch software modules and RadioPro manuals.
- RadioPro Solo: A Virtual Control-Station Radio on a Windows PCRadioPro Solo puts a virtual control-station radio on a Windows PC: Intercom, private calls, menus, installation and licensing.
- RadioPro Talk Mobile App: Connecting iPhone and Android Phones to a Two-Way Radio SystemHow the RadioPro Talk app connects Android and iOS phones to MOTOTRBO and NEXEDGE radio systems: setup, calls, maps, settings and Bluetooth PTT.
- The RadioPro Product Family: Dispatch, Solo and Talk ComparedHow RadioPro Dispatch, Solo and the Talk mobile app compare feature by feature, and what the IP Gateway does for all three on MOTOTRBO and NEXEDGE radio systems.
- Troubleshooting RadioPro Dispatch: Grayed-Out Controllers, Audio and Transmit ErrorsCauses and corrective actions when RadioPro Dispatch radio controllers are grayed out, audio is missing or delayed, or the transmit error window appears.
- Upgrading a RadioPro System: Gateway Firmware, Dispatch Software, Licenses and PC ReplacementHow RadioPro IP Gateway software is upgraded (field or return), how licenses are expanded, how Dispatch is upgraded and how a console is moved to a replacement PC.
MCN and BRSC Comparator Monitoring
- Base Radio Status Concentrator (BRSC): Transmitter Status from GTR 8000 Base RadiosThe Base Radio Status Concentrator is CTI software that gathers status from up to 240 Motorola GTR 8000 base radios and serves it to MCN Server 8000.
- ComparatorsHow a radio comparator makes its voting decision between simultaneous receiver audio feeds in a voting receiver system.
- Installing an MCN System: Addressing, Cabling, Mounting and PowerHow MCN modules are addressed with Group and Module numbers, receiver banks, network cabling limits, terminators, mounting and DC power chaining.
- MCN Engineered Systems: Large Networks with Routers and 1.25 Mbps BackbonesHow MCN systems scale beyond 20 comparator I/O modules with routers, a 1.25 Mbps backbone and factory-set addresses.
- MCN Monitoring and Control Network: Comparator Display System OverviewCTI's MCN is a modular network that displays and controls voting-receiver comparators from consoles and PCs: architecture, uses and examples.
- MCN Remote Comparator Display (MCNRCD) Software: Standard, Server and Client EditionsHow MCNRCD software shows comparator and I/O status on a PC, with its Standard, Server and Client editions, screens and error logging.
- MCN Server 8000: Monitoring Motorola GCM 8000 and MLC 8000 IP ComparatorsMCN Server 8000 monitors and controls Motorola GCM 8000 and MLC 8000 IP comparators plus legacy comparators, with clients over IP.
- MCN System Performance Toolkit: Detecting Inactive Receivers and Collecting Radio System StatisticsThe MCN System Performance Toolkit finds receivers and I/O points that never receive, vote or change state, and logs hourly system statistics.
- Troubleshooting MCN Modules: LEDs, Buttons and Common ProblemsWhat the PWR, ACT and ERR LEDs on MCN modules mean, what the reset button does, and the checks for display and control problems in an MCN comparator display system.
- Voting Receivers and ComparatorsA repeater's downlink (repeater-to-radio) range is often much larger than a portable or mobile radio's uplink (radio-to-repeater) range.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.