Repeaters and Antennas Basics

RF, Antennas and Radio Sites · Last updated · About 20 min read

This page covers the fundamentals of how repeaters extend the range of two-way radio systems, and basic antenna and site-engineering concepts that affect coverage in LMR (land mobile radio) systems.

What a Repeater Does

A radio repeater consists of a receiver connected to a transmitter: it receives a signal on one frequency and retransmits it, amplified, on a second frequency. Radios and dispatch consoles that are out of direct line-of-sight range of each other can still communicate because the repeater — typically mounted on a hilltop or tall building/tower — relays the signal between them.

Without a repeater, communication range is limited by the curvature of the earth and by terrain or building obstructions blocking line of sight. A repeater placed at an elevated site dramatically expands the effective coverage area by giving both the received and retransmitted signal a much better line-of-sight path than either end-user radio would have on its own.

This is the core mechanism behind Conventional-Radio-Systems.md and Trunked-Radio-Systems.md: a single repeater (or a network of repeaters, in trunked and simulcast systems) sits between radios and multiplies the area over which they can talk to each other.

Why Repeaters Need Distinct TX/RX Frequencies

A repeater must listen and transmit at the same time, on different frequencies (commonly called the input and output frequencies). If it listened and transmitted on the same frequency, the repeater's own powerful outgoing signal would swamp its sensitive receiver and it could not hear incoming transmissions.

To avoid this, the receive and transmit frequencies are offset from one another by a duplex offset (sometimes called the repeater "split") — a standard, conventional separation between the repeater's output (downlink) and input (uplink) frequencies that's specific to each band:

Band Standard Duplex Offset Notes
VHF (150–174 MHz high-band) 600 kHz The long-standing conventional split, most familiar from the amateur 2-meter band but also the common commercial VHF convention.
UHF (450–470 MHz) 5 MHz See UHF Radios for confirmed channel-pair examples; the amateur 70cm band uses the same 5 MHz convention.
UHF T-Band (470–512 MHz, shared with TV channels 14–20 in specific metro areas) 3 MHz An exception to the general UHF 5 MHz convention — see UHF Radios for the T-Band background.
800 MHz (806–870 MHz) 45 MHz See 800 & 900 MHz Radios for the confirmed channel-pair example and post-rebanding band structure.

These are conventions, not laws of physics — a licensee's actual assigned frequency pair is whatever the FCC (or equivalent regulator) grants, and the "standard" offset for a band is simply the split that channel plans, repeater coordination bodies, and manufacturer defaults have converged on for that band. Non-standard pairings do exist in the field (sometimes called "odd-split" repeaters), and a few specific sub-allocations (for example, some UHF broadcast-auxiliary frequencies) don't follow the general band convention at all — so a technician programming an unfamiliar system should always confirm the actual licensed input/output pair rather than assuming the standard offset applies.

How a Duplexer Works

A duplexer is the component that lets a repeater's transmitter and receiver share a single antenna despite operating simultaneously, close in frequency, with a huge power differential between the outgoing transmit signal (often tens of watts) and the incoming receive signal (often a fraction of a microwatt). Without isolation, the transmitter would desensitize or physically damage the receiver front end. Duplexers achieve this isolation using banks of cavity filters:

  • A cavity filter is a sharply tuned resonant circuit — physically, a metal cylinder ("cavity") with an internal tuning element and coupling loops at the input and output — that behaves like an extremely selective, high-Q version of a simple RF filter.
  • Cavities come in two flavors:
  • Bandpass (BP) cavities pass a narrow band of frequencies and reject everything else.
  • Band-reject / notch (BR) cavities do the opposite: they reject a narrow band of frequencies and pass everything else through largely unaffected.
  • A single bandpass cavity, on its own, cannot provide enough rejection at a typical repeater TX/RX offset (only a few dB at a few hundred kHz separation) to fully protect the receiver. Notch cavities provide much deeper, more targeted rejection at the specific "wrong" frequency (the transmit frequency, as seen by the receive leg, and vice versa).
  • Practical duplexers combine multiple notch and bandpass cavities in each leg (transmit leg and receive leg), connected by carefully cut lengths of coaxial cable so that the rejection/passband effects of each cavity add constructively. The result is a device that can isolate a receiver from a transmitter operating just a few MHz away by 80-100+ dB, while adding only a modest amount of insertion loss to the desired signal path.

Diagram of a repeater duplexer showing the transmit and receive cavity filter legs sharing a single antenna

Duplexers must be tuned (mechanically, via the cavities' tuning slugs or capacitors) to the specific frequency pair in use, and retuning is required if a repeater's frequencies change. This is why duplexers are treated as a precision, site-specific component rather than an off-the-shelf universal part.

There are several distinct duplexer and combiner architectures (notch, bandpass-reject, bandpass/window, hybrid, ceramic), each a different tradeoff of isolation, cost, channel count, and tolerance for other nearby transmitters — along with site-level rules of thumb for guard bands, Tx-Tx spacing, and total isolation budgets.

Repeater Timeout Timers and Courtesy Tones

Beyond the core receive/retransmit function, most repeaters implement a few standard operational safeguards:

  • Time-Out Timer (TOT) — automatically cuts off a transmission if a user holds the push-to-talk button down continuously beyond a configured limit (commonly on the order of a minute or less). This prevents a single stuck or forgotten transmission from tying up the channel indefinitely, and protects the repeater's transmitter from thermal damage due to excessively long duty cycles.
  • Courtesy tone — a brief tone the repeater emits after a transmission ends, signaling to other users that the channel is clear and it's safe to key up again without stepping on the tail end of the previous transmission (particularly useful on repeaters with a hang time/carrier-delay before the repeater drops its own carrier).
  • Hang time — a short delay the repeater's own transmitter holds open after the last received signal ends, so a follow-up transmission from another user doesn't have to wait through a full repeater-drop/re-key cycle, at the cost of tying up the channel slightly longer per exchange.

These features apply across conventional, trunked, and simulcast repeater deployments, though trunked systems typically manage timeout and channel-release behavior at the network/controller level rather than per physical repeater.

Antenna Basics for LMR Coverage

Antenna height and placement are major factors in how far a radio system's coverage reaches:

  • Height matters. Mounting an antenna higher — on a tower, tall building, or hilltop — extends the radio line-of-sight horizon and lets a signal clear terrain and building obstructions that would otherwise block it. This is the same principle that makes repeater sites effective: elevation, not raw transmitter power, is often the biggest lever for extending coverage.
  • Frequency affects antenna size and behavior. Lower-frequency (VHF) systems generally travel farther in open terrain but require physically longer antennas — sometimes several feet tall on a vehicle — to efficiently capture the signal. Higher-frequency systems (UHF, and especially 800/900 MHz) use physically shorter antennas that inherently collect less energy, and their shorter wavelengths are attenuated more by foliage and other obstructions.
  • Higher-frequency systems are more sensitive to antenna placement. Because 800/900 MHz signals do not diffract around obstacles as readily as lower-frequency signals, and because their antennas are physically smaller and less efficient at capturing signal, coverage at these frequencies is more sensitive to exact antenna placement, height, and line-of-sight obstructions than lower-band VHF/UHF systems.

Antenna Gain: dBi vs. dBd

Antenna "gain" does not mean an antenna adds energy to a signal — no antenna is an amplifier. Instead, gain describes how much an antenna concentrates a fixed amount of radiated energy into a particular direction (or, for a receive antenna, how much more effectively it captures energy arriving from that direction) compared to a reference antenna. Two reference antennas are commonly used, which is why gain figures are stated in two different units:

  • dBi — gain relative to a theoretical isotropic radiator, an idealized antenna that radiates equally in every direction (like a point source at the center of a sphere). This is the "purest" mathematical reference.
  • dBd — gain relative to a real, simple half-wave dipole antenna, which itself has a gain of about 2.15 dBi.

Because a dipole is already a slightly directional (better than isotropic) radiator, the two scales differ by a fixed offset:

Gain (dBd) ≈ Gain (dBi) − 2.15

A dBi figure for a given antenna is always the larger number, which is one reason manufacturers often prefer to publish dBi specs — they look more impressive even though the antenna's real-world performance hasn't changed. When comparing antenna spec sheets (e.g., choosing between two repeater-site omni antennas or two Yagis), it's important to confirm whether the gain figures are in dBi or dBd before comparing them directly, since a "6 dBd" antenna and a "6 dBi" antenna are not equivalent (the 6 dBd antenna is actually about 2 dB "hotter").

Effective Radiated Power (ERP/EIRP)

Antenna gain and transmitter power combine to determine how much power a signal effectively radiates in its strongest direction:

ERP (or EIRP) = Transmitter power x Antenna gain (as a ratio, not dB)

Because gain in dB is a logarithmic ratio, a dBi figure has to be converted back to a plain multiplier before multiplying: Multiplier = 10^(dB/10). For example, a dipole's 2.15 dBi gain works out to a multiplier of about 1.64x, so a 100 W transmitter feeding a dipole antenna produces an EIRP of about 100 W x 1.64 = 164 W in the antenna's strongest (horizontal) direction — even though no power was actually "created." This is the same principle described above for dBi/dBd: gain concentrates existing power rather than adding to it, but from a receiver's point of view at the strongest point of the pattern, it looks exactly like 164 W would have looked radiated from an isotropic source. A quick reference for converting common dB gain/loss figures to power multipliers:

dB Power multiplier dB Power multiplier
1 1.26x 10 10x
3 2.00x 15 32x
6 3.98x 20 100x
8 6.31x 30 1,000x

(Negative dB values, i.e., losses, give the reciprocal multiplier — e.g., -3 dB is a 0.5x multiplier, -10 dB is a 0.1x multiplier.)

Beamwidth and Front-to-Back Ratio

Beyond the dBi/dBd gain figure, two more antenna-pattern specifications matter in practice:

  • 3 dB beamwidth — the angular width of an antenna's main lobe, measured between the two points where radiated power has dropped to half (3 dB down) of its peak value. A narrower beamwidth concentrates more energy into a smaller angular slice (higher gain), at the cost of needing more precise aiming — the same tradeoff described for parabolic dishes in Dish Antennas and Point-to-Point Links. For a vertically-polarized antenna, a narrow vertical beamwidth can actually create a coverage problem at very tall sites: a high-gain omni antenna with a 7-degree vertical beamwidth on a 750-foot tower places its half-power point at only about 2.3 miles out from the base, while the same antenna on a 5,000-foot mountaintop site pushes that point out to roughly 15 miles — potentially leaving a coverage gap close in to the tower ("down-fill"). Site engineers address this either with electrical or mechanical down-tilt (aiming the main lobe slightly toward the ground) or by choosing a different gain/beamwidth tradeoff for the site's height.
  • Front-to-Back (F/B) Ratio — for a directional antenna like a Yagi, this describes how much weaker the antenna's response is directly behind it (180 degrees from the main lobe) compared to its peak forward gain, typically in dB (a well-designed Yagi might have an F/B ratio around 16 dB). Real-world antenna patterns also have minor lobes and nulls — smaller, less predictable peaks and dips off the main beam axis — which matter when calculating actual radiated power in a specific unwanted direction, since a deep null a few degrees off the main beam can reduce effective power in that direction far more than the F/B ratio alone would suggest.

Common LMR Antenna Types

Different antenna geometries serve different roles in an LMR system:

  • Omnidirectional (omni) antennas — whip and collinear. These radiate (and receive) roughly equally in all horizontal directions, which is exactly what's needed at most repeater sites, where the repeater must be able to hear and be heard by mobile/portable radios scattered in every direction around the site. A simple whip is a single vertical element; a collinear antenna stacks multiple radiating elements vertically (in phase) to squeeze more gain out of the omnidirectional pattern by flattening the radiation pattern into a wider, flatter disk aimed toward the horizon rather than wastefully radiating energy up into the sky or down into the ground. Collinear antennas are a very common choice for repeater-site master/base antennas because they add gain without sacrificing the 360-degree coverage a repeater needs.
  • Directional antennas — Yagi and panel. These concentrate energy toward one specific direction/target rather than spreading it in all directions, trading coverage breadth for range and gain in that one direction.
  • A Yagi (Yagi-Uda) antenna — first developed in Japan in 1926 by Hidetsugu Yagi and Shintaro Uda — uses a driven element (the radiator) plus a series of parasitic elements: a longer reflector behind the radiator and one or more shorter directors in front of it, all arranged along a boom. The physical spacing and length of these elements determine how much of the radiator's energy is concentrated into the forward lobe, giving high directivity and gain in an open, visibly "elements on a boom" mechanical form, at low weight, low wind drag, and modest cost. Yagis are a common choice for point-to-point links (e.g., a remote repeater site relaying back to a central site) or for a fixed base station that only ever needs to talk to one other location. A related but simpler directional design is the corner-reflector antenna: a dipole placed a quarter-wavelength in front of a right-angle V-shaped (or closely spaced rod) reflector screen, which redirects energy that would otherwise radiate to the rear back through the dipole and out the front — the same principle, scaled up into a curved bowl shape, that produces a parabolic dish antenna.
  • A panel antenna achieves similar directional gain in a flat, enclosed, weatherproofed package — mechanically more compact and often preferred for tower-mounted sector coverage (e.g., covering one direction/sector of a multi-antenna site) where a visible open Yagi structure would be impractical or aesthetically undesirable.
  • Both Yagi and panel antennas must be physically aimed at the target and are unsuitable for a repeater that needs to serve mobiles in every direction — that role is reserved for omni/collinear antennas.
  • Parabolic dish antennas. For long-distance, high-frequency point-to-point microwave links (for example, linking two repeater sites together, or backhauling a remote site to a network core), LMR systems often use parabolic dish antennas rather than Yagi/panel/omni designs. Dishes provide very high gain and very narrow beamwidth, but operate on different frequency bands and engineering considerations than the VHF/UHF/800-900 MHz antennas described above.

Antenna Length and Impedance Matching (VSWR)

Most LMR antennas are built around the half-wave dipole as their fundamental radiating element (even the collinear, Yagi, and panel designs above are built from arrays or variants of dipole elements). A simple rule of thumb for a half-wave dipole's physical length is:

Length (inches) ≈ 492 ÷ frequency (MHz)

This is why antenna length scales inversely with frequency: a half-wave element is roughly 39 inches at 150 MHz (VHF) but only about 13 inches at 450 MHz (UHF) — the same physical relationship discussed in VHF Radios and UHF Radios.

For maximum power transfer, an antenna's impedance must be matched to its feedline's impedance (almost always 50 ohms in LMR systems, versus 75 ohms commonly used for cable TV/CATV). A transmission line's characteristic impedance (Zo) is not simply its DC resistance — it's derived from the cable's per-unit-length capacitance, inductance, resistance, and conductance (the Telegrapher's equations), and for a well-designed RF cable it stays essentially constant across the operating frequency range. This matters practically because a matched line (Zo equal to the load/antenna impedance) presents that same impedance at the transmitter no matter the cable's length or the frequency in use — so an installer can use whatever practical cable length a site requires without having to cut it to a precise resonant length. A mismatched line (Zo different from the load impedance), by contrast, causes the impedance seen at the transmitter to vary with both cable length and frequency, an unpredictable condition normally avoided by keeping the whole system — transmitter, feedline, and antenna — consistently at 50 ohms. A mismatch causes some of the transmitter's power to reflect back down the feedline instead of radiating, an effect measured as Voltage Standing Wave Ratio (VSWR). VSWR is expressed as a ratio referenced to a perfect 1.0:1 match; a VSWR of 1.5:1 corresponds to about 96% of the power actually reaching the antenna (4% reflected), while a poor 2.0:1 match lets only about 89% of the power through. Because reflected energy bounces back toward the transmitter, an excessive VSWR can also stress or damage the transmitter's output stage over time, in addition to wasting radiated power. Field technicians commonly verify VSWR with a wattmeter/service monitor, or a distance-to-fault (DTF) test set, which can also help localize a specific bad connector or cable defect along a feedline run. Note that a VSWR/DTF test measures impedance matching, not the different phenomenon of passive intermodulation (PIM) — a feedline can pass a VSWR test cleanly while still failing a PIM test, or vice versa.

PIM ratings. On any site combining multiple transmitters onto shared antennas, the antenna itself is one of the most important components to get right from a PIM standpoint.

Feedline (Coax) Loss

The cable connecting a radio or repeater to its antenna — the feedline, almost always coaxial cable in LMR systems — is not lossless. Some of the transmitter's power (and some of the received signal's strength) is absorbed by the cable itself before ever reaching the antenna or radio, through two combined mechanisms:

  • Conductor loss — resistive loss in the center conductor and shield, which grows with frequency due to the "skin effect" (at higher frequencies, current is forced to flow in a thinner layer near the conductor's surface, increasing effective resistance).
  • Dielectric loss — energy absorbed by the insulating material between the conductors, which also increases with frequency.

Two practical rules of thumb follow directly from this:

  1. Loss increases with frequency. The same cable run has more loss at 900 MHz than at 150 MHz. For example, a popular low-loss cable like LMR-400 is rated at roughly 2.6 dB per 100 feet at 100 MHz but roughly 6.6-6.7 dB per 100 feet at 400-900 MHz — more than double the loss for the same length of cable, simply because the frequency is higher.
  2. Loss increases (linearly) with length. Doubling the length of a cable run roughly doubles its loss in dB. A repeater site with a long run from the equipment room up to a tower-top antenna will lose meaningfully more signal than a short run to a mast-mounted antenna, all else equal.

Because of this, site engineers select feedline based on frequency, run length, and acceptable loss budget — sometimes choosing a larger-diameter, lower-loss cable (at higher cost and reduced flexibility) specifically to keep loss acceptable on a long run at UHF or 800/900 MHz, or relocating equipment (e.g., a repeater mounted near the top of the tower) to shorten the run entirely.

Coaxial Cable Types and Real-World Loss Figures

LMR/site coax generally falls into three construction categories, each a different tradeoff of loss, cost, and durability:

  • Solid (foam) dielectric cable — a solid copper-clad-aluminum or copper center conductor surrounded by foam-polyethylene insulation and a corrugated copper or aluminum outer conductor (e.g., Andrew/CommScope HELIAX LDF4-50A, a common 1/2-inch size). This is the standard choice for most tower feedline runs: moderate cost, no pressurization required, and long service life.
  • Air dielectric cable (e.g., HELIAX HJ7-50A, a 1-5/8-inch size) — uses an air gap (supported by spacers) instead of solid foam as the dielectric, giving the lowest loss and highest power handling of the three types, at the cost of much larger diameter/weight, higher price, and a requirement to keep the line pressurized with dry air or nitrogen to keep moisture out.

The following manufacturer-published attenuation figures illustrate just how large the differences are across cable types, sizes, and frequency:

Cable Size Attenuation @ 150 MHz (dB/100 ft) Attenuation @ 450 MHz (dB/100 ft) Attenuation @ 900 MHz (dB/100 ft)
HELIAX FSJ4-50B (superflexible foam) 1/2 in ~1.29 ~2.31 ~3.38–3.52
HELIAX LDF4-50A (standard foam) 1/2 in ~0.82 ~1.45 ~2.09–2.17
HELIAX HJ7-50A (air dielectric) 1-5/8 in ~0.25 ~0.45 ~0.66–0.69

As the table shows, moving from a flexible 1/2-inch cable to a rigid 1-5/8-inch air-dielectric cable can cut loss by a factor of roughly 3, at the cost of a much larger, heavier, harder-to-install (and pressurized) cable — the same fundamental "bigger and lower-loss vs. smaller and more convenient" tradeoff introduced above, now with concrete numbers.

Connectors

The connector at each end of a feedline run matters as much as the cable itself. Common LMR/tower connector types include:

  • Type-N — a long-standing industry-standard connector rated well above 300 MHz (some designs to 10+ GHz), but a 1940s-era design not built with PIM performance in mind; not recommended for high-power multicarrier transmit paths.
  • UHF (PL-259/SO-239) — an older, simple, rugged connector still common on lower-power/lower-frequency (under ~300 MHz) equipment, valued for how easy it is to install in the field.
  • BNC/TNC — smaller quick-disconnect connectors (BNC is a bayonet-style twist-lock, TNC adds threaded coupling for vibration resistance) typically used on test equipment and lighter interconnects rather than main tower feedlines.

Regardless of connector type, proper installation — using the cable manufacturer's dedicated prep tool (never a knife or hacksaw, which leaves metal shavings behind), torquing every connection to its specified value, and weatherproofing every outdoor connection with butyl tape or heat-shrink tubing — determines whether a feedline run performs to its rated loss and PIM specifications over its service life, or degrades early from moisture ingress and loose connections.

Tower and Site Engineering Basics

Selecting and engineering a repeater or base station site involves more than just "put the antenna up high":

  • Height Above Average Terrain (HAAT). Because raw antenna height above ground doesn't account for the surrounding landscape, engineers commonly use HAAT — an antenna's height above the average elevation of the surrounding terrain (typically averaged over multiple radials extending several kilometers out from the site) — as a better predictor of effective coverage than height above ground alone. A modest tower on a high ridge can have a much greater HAAT, and therefore much better coverage, than a taller tower sitting in a valley.
  • RF exposure and safety. The FCC sets Maximum Permissible Exposure (MPE) limits for radiofrequency electromagnetic fields (47 CFR 1.1310), with different (more permissive) limits for "controlled/occupational" environments — where workers are trained, aware of the RF hazard, and can control their exposure, such as tower climbers and technicians — versus stricter limits for "uncontrolled/general public" environments. Exposure limits are most restrictive around VHF frequencies (roughly 30-300 MHz), which is close to the whole-body resonance frequency of an average adult standing on the ground, meaning the body absorbs RF energy most efficiently in that range.
  • Lightning protection. A tall metal tower is a natural lightning target, but this can be turned into an advantage: properly grounding the tower structure itself (base, footings, and guy-wire anchors, with buried ground rings/rods) gives a strike a controlled, low-resistance path to earth that protects the more sensitive components mounted on and around it. Additional site-specific measures include a lightning rod positioned above tower-top antennas, a quarter-wave shorting stub inserted in the antenna feedline (sized so it has no effect at the operating frequency but presents an immediate short circuit at lightning's much lower effective frequencies), and surge protection devices (SPDs) installed on the DC power system and at cable entry points into equipment shelters — conceptually the same kind of protection as a home surge protector, sized for tower-scale strikes. Cloud-to-ground lightning (the type that threatens ground-based equipment) differs from cloud-to-cloud lightning, which discharges entirely within the atmosphere and poses no risk to towers.
  • Tower climbing hazards. Tower climbers face among the highest RF exposure risks of any occupation, because working near an active antenna aperture can expose a person to field strengths far above the MPE limit for even brief periods. Standard practice is to power down or reduce power on co-located transmitters before climbing near their antennas, and for climbers to wear personal RF exposure monitors. These are safety practices reported on by OSHA and the EPA rather than OSHA-specific regulations, since RF exposure limits themselves are set by the FCC.

References

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.