Connecting a RadioPro IP Gateway to Kenwood NEXEDGE Control-Station Radios

RadioPro and CTI Products · Last updated · About 6 min read

Kenwood FPU settings for NEXEDGE control-station, data revert and subscriber radios (NX-700/800, 720/820, 3720/3820, 5700/5800) used with RadioPro.

This article summarizes how Kenwood NEXEDGE radios are prepared for a RadioPro IP Gateway. Radio background: kenwood-nexedge-overview, kenwood-nexedge-nx-700-800, kenwood-nexedge-nx-720-820, kenwood-nexedge-nx-3720-3820, kenwood-nexedge-nx-5700-5800, nxdn-digital-standard and programming-kenwood-nexedge-radios. General gateway steps are in radiopro-ip-gateway-installation-and-configuration.

Radios and minimum firmware

Control-station radio Minimum firmware Kenwood programming software
NX-700/800 or NX-720/820 (and NX-3720/3820) 3.21.00 KPG-111DN FPU
NX-5700/5800 (the 57xx guide calls it the preferred radio) 2.31.00 KPG-D1N FPU

Each control-station radio used for voice needs one gateway. The NX-700/800 is easiest to implement because the NX-720/820 and NX-3720/3820 need a modification to the option jumpers on the radio's Tx/Rx unit. A separate cable connects a dedicated data revert radio. A programming cable on the front microphone connector may prevent communication through the rear connector, so disconnect it before attaching the gateway.

Feature support by system type is in radiopro-dispatch-feature-availability-by-system-type. In the Kenwood table, analog-only systems get voice dispatch only; selective calling is not currently supported on NXDN with call acknowledge or on NXDN message-trunked systems.

Interface cables

Radio Voice cable Data revert cable
NX-700/800, NX-5700/5800 S2-61769 (DE-9 male to DB-25 male) 89-10505 (DE-9 female to DB-25 male, a standard serial cable)
NX-720/820, NX-3720/3820 S2-61890 (DE-9 male to DE-15 male) S2-61891 (DE-9 female to DE-15 male)

The two kinds of cable have opposite connector genders at the gateway end: the voice cable's DE-9 male plugs into the gateway's female connector, and the data revert cable's DE-9 female plugs into the gateway's male serial port. They are not interchangeable. A NEXEDGE gateway supports only one data revert radio (radiopro-data-revert-radios). All RadioPro part numbers are listed in radiopro-part-numbers-and-ordering.

Pinout of voice cable S2-61769 (NX-700/800 and NX-5700/5800). The audio pairs are transformer isolated at 600 ohms.

Signal IP Gateway DE-9 pin Radio DB-25 pin
Tx+ (mic audio to radio) 4 6
Tx− (mic audio to radio) 5 25
Rx+ (speaker audio from radio) 8 17
Rx− (speaker audio from radio) 9 18
Tx data (from radio) 1 3
Rx data (to radio) 6 2
Digital ground 3 7

Pinout of data revert cable 89-10505. It carries data lines and ground only, because a data revert radio carries no audio.

Signal IP Gateway DE-9 pin Radio DB-25 pin
Tx data (from radio) 2 3
Rx data (to radio) 3 2
Digital ground 5 7

The pinouts for the DE-15 cables of the NX-720/820 and NX-3720/3820 are in the installation guide's appendix.

Control-station (voice) radio settings, NX-7xx/8xx and NX-37xx/38xx (KPG-111DN)

  1. Read the radio, then import the saved system settings (or enter them manually).
  2. Data port: Edit, Optional Features, Optional Features 1, Common Page 3: set the COM port 1 function to Data + GPS Data Output and the PC Interface Protocol to Version 2 (Version 1 prevents the gateway from working). On Common Page 4 check the Short Message Stack, Latest Received Message Stack and Message Memory options and all Serial Output and Serial Input options.
  3. Sound: Extended Function, Modulation Line tab: set Mic PTT to Connect for the MI2 column. AUX tab: set Mic Sense to 4 dB (High). Mobile Function tab: set DEO level (the level into the computer) to +5; DI and DEO levels can be adjusted as needed. These FPU settings, not the gateway, are where NEXEDGE audio levels are adjusted: the gateway has no level control of its own (audio-clipping).
  4. FleetSync and NXDN IDs: a FleetSync Fleet (Own) and ID (Own), and an NXDN Unit ID (Own), must be assigned even if the radio is used in analog mode without FleetSync or in NXDN digital mode. Without them RadioPro will not function properly.
  5. Data channel: for each zone, assign the Data Zone-CH/GID for analog and digital as the system requires. For a conventional system, enable the wanted message types to be sent on the data channel in the FleetSync Parameter tab or the NXDN Conventional tab.
  6. GPS: Optional Features 2, GPS tab, Base Station Settings: check $PKLDS/$PKNDS (KW). Without it, GPS data is not sent to the gateway.

NX-5700/5800 (KPG-D1N) differences

  • In Personal, System 1, System Information choose NXDN Conventional for system type and FleetSync for signaling type, and assign Fleet (Own), ID (Own) and Unit ID.
  • Optional Features 1, Serial Interface: COM port 1 function Data + GPS Data Output, COM Port Priority Serial Data, PC Interface Protocol Version 2, and all Serial Output and Serial Input options checked.
  • Optional Features 2, GPS page, Base Station Settings: $PKLDS/$PKNDS (KW) checked.
  • FleetSync Information and NXDN Information: enable all Serial Output options except Transparent Header, and enable all Stack options.
  • Audio Profile: Microphone Sense +4 dB (High). Extended Function, Modulation Line: Mic PTT = Connect for both the Mic Line and MI2 Line. (The sound and audio-routing steps can be skipped for a radio used only for GPS.)

Data revert radio

Configure it like the voice radio, except: skip the sound options (it handles no audio), skip the data-settings step (it only receives GPS), follow the GPS step, and program only the data channel (channel steering only affects the voice radio).

Subscriber radios (ARS, GPS and text)

  • Configure the radio as normal, then set its target: with FleetSync, the Target Fleet and Target ID must specify the control-station radio; with NXDN, the Base ID must specify the control station. If the target does not include the control station, data will not appear in RadioPro clients.
  • Data channel: the Data Zone-CH/GID values must be the same as in the control-station radio, with the wanted messages enabled. In NXDN conventional, disabling "Status message on Data Zone-CH/GID" keeps the radio check on the voice channel.
  • Text messages: in Key Assignment, Menu tab, add the SDM (FleetSync/NXDN) function from the Call category.
  • GPS: to send GPS on another channel, check GPS Report on Data Zone-CH/GID and choose the channel. For FleetSync set the GPS Base Fleet and Base ID, and for NXDN the GPS Base ID Type and Base ID. The NXDN GPS base ID is the ID of the data revert control-station radio, which the subscriber responds to.
  • Data port: set COM port 1 to None and enable the Short Message Stack.

ICU settings for NEXEDGE

  • NEXEDGE Radio tab: the appropriate radio ID values, and a Receive PTT ID timeout (ms) that gives the transmitting radio time to send its PTT ID before the default PTT ID is used.
  • GPS tab: check Start GPS polling when online status received if subscriber locations are to be mapped (leave it unchecked if mapping is not needed or the subscribers start polling on their own), and set the Report interval, the minimum time between GPS updates. A longer interval means fewer updates and more bandwidth for voice.

See also radiopro-dispatch-gps-mapping-and-geo-fences.

Source documents

This article summarizes the following published CTI Products manuals. They are the authoritative reference.

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.