Simulcast
What Simulcast Means
Simulcast ("simultaneous broadcast") is a technique where two or more repeater sites transmit on the exact same frequency, with the exact same modulation, at the exact same instant, so that from a listening radio's perspective the whole network behaves like one enormous "super repeater" covering all the sites combined. This lets a single logical channel cover a wide geographic area — a user can roam between sites without touching a channel selector, because they never actually leave the one frequency.
How Simulcast Uses GPS
GPS is the practical mechanism that makes site-to-site synchronization possible without running a dedicated timing cable between every tower. Each transmitter site has a GPS-disciplined oscillator (see GPS): a GPS receiver extracts a precise one-pulse-per-second (1PPS) timing reference from the satellite signal, and that reference steers a local oscillator so every site's transmitter clock stays phase-locked to the same time standard. Because every site is disciplined against the same GPS time rather than against each other directly, a simulcast controller only needs to tell each site when (by that shared clock) to transmit a given piece of audio, and every site's local GPS-locked oscillator ensures it does so at the correct instant.
This tolerance isn't infinite: digital simulcast systems (DMR, P25, TETRA) use adaptive equalization and symbol-timing recovery to absorb a limited amount of timing/delay-spread error between sites, similar in concept to the guard interval used in digital broadcast systems to prevent multipath echoes from causing inter-symbol interference. If GPS lock is lost at a site (e.g. due to antenna failure or satellite visibility issues), that site's timing will eventually drift out of tolerance and it may need to be dropped from the simulcast cell until GPS lock is restored.
Advantages and Challenges
Advantages: fewer frequencies are needed for wide-area coverage (simplifying frequency coordination), and users experience seamless roaming with no manual channel changes.
Challenges: simulcast infrastructure and synchronization equipment add cost, and in "overlap" zones where two or more sites' signals arrive at a receiver simultaneously with a slight delay (delay spread), the resulting audio can become distorted or unintelligible — a failure mode similar to multipath fading, and something simulcast network designers must specifically account for during site planning.
Overlap-Zone Audio Artifacts in Detail
- Delay spread and cancellation nulls (the core simulcast-specific mechanism): in an overlap zone, a receiver picks up two (or more) transmitters' signals at nearly — but not exactly — the same instant and with similar strength, because they traveled different distances from their respective sites. Even though every site's RF carrier frequency, modulation level, and modulation phase are deliberately equalized as closely as possible during simulcast system design specifically to minimize this, small residual differences in timing/phase between the arriving copies can cause them to partially or wholly cancel at certain instants (a "cancellation null") when they arrive close enough to 180 degrees out of phase — sometimes described informally as a comb-filtering effect, since (much like an audio comb filter) the cancellation is frequency-dependent, hollowing out parts of the signal rather than just uniformly weakening it. On a digital simulcast system, this same delay spread shows up as an elevated bit error rate rather than analog-style audio distortion, since the receiver's demodulator is working from a corrupted composite RF waveform.
- "Picket fencing" — a related, frequently-used term, but worth using carefully: in its more precise, traditional sense, picket fencing describes the rapid audio flutter/chopping a moving receiver experiences from ordinary multipath (the signal reflecting off buildings, terrain, vehicles, etc., interfering with itself as the receiver moves — even from a single transmitter site) — named for how it sounds like listening to something through a picket fence while walking past it. Because a simulcast overlap zone is inherently a more RF-complex environment (multiple transmitted copies of the same signal plus each one's own local multipath), listeners and even some technical sources use "picket fencing" loosely to describe overlap-zone choppiness too, even though the strict multipath definition and the simulcast-specific delay-spread/cancellation-null mechanism above are technically distinct phenomena that happen to sound similar. When troubleshooting, it's worth distinguishing which is actually happening: true single-site multipath picket fencing typically clears within about a wavelength of receiver movement, while overlap-zone delay-spread degradation is tied to a receiver's position relative to both transmitter sites and won't clear with small movements the same way.
Related Pages
References
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.