Kenwood NEXEDGE NX 720 820

Kenwood and NXDN · Last updated · About 3 min read

Overview

The NX-720 (VHF) and NX-820 (UHF) are Kenwood NEXEDGE mobile radios that followed the earlier NX-700/NX-800 generation. As with other NEXEDGE mobile pairs, the lower number (NX-720) is the VHF variant and the higher number (NX-820) is the UHF variant. High-power/GPS variants were sold as NX-720G/NX-720HG and NX-820G/NX-820HG.

Sourced Comparison Against NX-700/800

A RadioReference forum thread comparing the NX-700/800 and NX-720/820 (title: "NX-700 vs NX-720 - used market value") lays out the following technical deltas directly:

Spec NX-700/800 NX-720/820
Channel capacity 512 channels 260 channels
Display 14-character alphanumeric 10-character alphanumeric
NEXEDGE trunking 6.25 kHz and 12.5 kHz 6.25 kHz only
Remote head kit Available (KRK-10) Not available

In other words, the NX-720/820 is a lighter/simpler successor rather than a strict superset upgrade — it trades some channel capacity, display length, and trunking-bandwidth flexibility for cost, while adding the GPS, FleetSync II/MDC-1200, and remote-management features described below. The same thread notes NX-720/820 units are comparatively abundant and inexpensive on the used market versus scarcer, pricier NX-700/800 units, consistent with the NX-720/820 being the newer, higher-volume, lower-cost product.

Key Features

  • NXDN digital and FM analog operation on the same radio, at 12.5 kHz and 6.25 kHz (digital) and 25 kHz/12.5 kHz (analog) channel spacings (Kenwood's spec sheet lists analog spacing as 12.5/15/25/30 kHz for the NX-720 and 12.5/25 kHz for the NX-820).
  • Operating modes: analog simplex, analog conventional repeater, analog LTR conventional trunking, NXDN conventional, and NXDN trunked/trunked-IP-network operation.
  • 260 channels/Group ID across 128 zones, maximum 250 channels per zone.
  • 10-character alphanumeric backlit LCD display, 6 front programmable function (PF) keys plus 4 up/down selectors, and 4 W speaker audio.
  • Voice channel-number announcement capability.
  • Built-in GPS receiver on "G"-suffixed models (requiring a separate GPS antenna), for vehicle location tracking.
  • FleetSync II and MDC-1200 signaling support, NXDN 16-bit encryption/scrambling, and remote stun/kill/check radio-management functions.
  • Status messaging, data capability, and over-the-air programming/alias updates.
  • Ruggedized to MIL-STD-810 C/D/E/F/G environmental standards, with IP54 water and dust intrusion protection.

Power and Frequency

  • NX-720 (VHF): 136–174 MHz, RF output at 50 W/30 W/5 W selectable levels (up to 50 W on the high-power NX-720H/NX-720HG).
  • NX-820 (UHF): 400–470 MHz or 450–520 MHz depending on variant, RF output at 45 W/30 W/5 W selectable levels (up to 45 W on the high-power NX-820H/NX-820HG).

Additional Specifications (per Kenwood spec sheet)

  • Dimensions: 6.30 x 1.69 x 5.35 in (160 x 43 x 136 mm).
  • Weight: 2.64 lb (1.2 kg).
  • Operating voltage: 13.6 V DC ± 15%.
  • Operating temperature range: -22°F to +140°F (-30°C to +60°C).
  • Frequency stability: ± 1.0 ppm.

What Improved Over NX-700/800

Compared to the earlier NX-700/NX-800 generation, the NX-720/NX-820 line added built-in GPS on "G" variants, FleetSync II/MDC-1200 compatibility, and remote radio-management functions (stun/kill/check), while continuing full support for mixed analog and NXDN digital operation and NEXEDGE trunked networking. As shown in the comparison table above, this came with some trade-offs — lower channel capacity, a shorter display, single-bandwidth (6.25 kHz-only) trunking, and no remote-head accessory — relative to the NX-700/800 it replaced.

Typical Use Cases

Cost-conscious fleets and public/private agencies wanting NXDN digital trunking with vehicle-location (GPS) tracking, legacy analog LTR trunking compatibility, and status/data messaging — a step up from the earlier NX-700/800 generation in cost-efficiency (if not raw channel/trunking capacity), and a predecessor to the multi-protocol NX-3720/NX-3820 series.

References

See also: CTI product documentation

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.