COR and PTT Interfacing
What COR and PTT Are
COR (Carrier Operated Relay, also called COS — Carrier Operated Squelch/Switch) and PTT (Push-to-Talk) are the two simplest, oldest, and most universal control signals on a two-way radio's accessory connector:
- COR/COS is an output from the radio: a logic-level signal (a voltage that flips high or low) that indicates whether the radio's squelch has opened — i.e., whether it is currently receiving a signal. In modern solid-state radios, this logic transition is used to drive a relay, transistor, or optoisolator, which some other device (a repeater, logger, or gateway) can watch to know "this radio is hearing someone talk right now."
- PTT is an input to the radio: the standard signaling convention is a closure to ground (0V) that commands the radio to key up and transmit, exactly mimicking what happens when a human presses the physical PTT button.
Alongside these two logic signals, a basic interface also carries plain analog Tx/Rx audio — the receive audio coming out of the radio, and transmit audio going into it.
Why This Interface Matters
Because COR/PTT/audio is a lowest-common-denominator interface — implemented in some form on nearly every commercial two-way radio ever made, regardless of manufacturer or whether the radio is analog, DMR, NXDN, or P25 — it lets a gateway or interconnect device support "any radio with standard COR/PTT data lines" without needing to speak that radio's specific digital control protocol at all. The tradeoff is that a COR/PTT interface can only do what those simple signals allow: key the radio to transmit, receive its audio, and know when it's receiving — it cannot switch channels/talkgroups, read status, or exercise any digital-only feature, because those require a real digital control interface (like MOTOTRBO's ARS/MNIS, or a manufacturer-specific control head/data protocol) rather than a bare logic-and-audio connection.
Signal Polarity — the setting that actually breaks installs
COR and PTT are only "simple" until you wire one up backwards. Neither signal has a universal polarity, so both ends must agree, and the Gateway exposes this as an explicit choice:
PTT output (Gateway → radio)
- Active Low — the radio expects the PTT line high when idle, pulled low / to ground when transmitting. (This is the classic "closure to ground" convention.)
- Active High — the radio expects the PTT line low / ground when idle, pulled high when transmitting.
COR / activity-detect input (radio → Gateway)
- Active Low COR — line held high when not in a call, pulled low / to ground when a transmission is received.
- Active High COR — line held low / grounded when idle, pulled high when receiving.
A polarity mismatch does not produce a dead interface — it produces a inverted one, which is why it can be confusing in the field: an inverted COR makes the Gateway think the radio is receiving constantly (and idle when it actually is receiving), and an inverted PTT can leave the radio keyed permanently.
When There Is No Usable COR — VOX
If a radio exposes no COR line, or an unreliable one, the Gateway can fall back to VOX (voice-operated switch) and infer an incoming call from the audio itself:
- VOX enabled — the Gateway decides a call is incoming from the Activation level (dB).
- VOX disabled — the Gateway decides from the COR signal.
- Deactivation hangtime (ms) holds the incoming audio up after the last "good" audio level, so normal speech gaps don't chop the call.
VOX is the practical answer for generic Rx/Tx (-BGL, or -AGA for APX; formerly -BGA) installs on radios whose accessory connector doesn't offer a clean carrier-detect output.
Full-Duplex and the "Bonk"
A related Gateway setting, Allow transmission while receiving, should only be enabled for radios genuinely capable of full duplex. With it disabled, a client that tries to transmit while a call is being received gets a bonk — which is expected behaviour on a half-duplex radio, not a fault. The APX 4500, for instance, is not full duplex, so this is left disabled and the bonk is normal.
Related Pages
References
- RadioPro IP Gateway Installation Guide for Motorola APX 4500 P25 Radios (Version 9), CTI Products — current v9 path; the polarity, VOX, and full-duplex detail above comes from this guide
- Simple Carrier Operated Relay, Telematika
See also: CTI product documentation
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.