Connecting a RadioPro IP Gateway to a Motorola APX 4500 P25 Control Station

RadioPro and CTI Products · Last updated · About 4 min read

How the RadioPro IP Gateway connects to a Motorola APX 4500 through an intercom (COR/PTT) interface, with ICU settings and P25 feature limits.

A RadioPro IP Gateway can connect a Motorola APX 4500 P25 mobile radio to RadioPro clients. See motorola-apx-4500 and p25-project-25 for radio and standard background, and cor-and-ptt-interfacing for general information about COR and PTT lines. General gateway steps are in radiopro-ip-gateway-installation-and-configuration.

An intercom interface

The gateway connects to the APX 4500 through an intercom interface that uses the COR and PTT functions always available on the radio's accessory connector. Therefore no special radio programming is needed to connect to the APX 4500. The gateway interface cable goes between the gateway's DE-9 connector and the 26-pin rear accessory connector on the radio. The Motorola programming cable must be used with CPS for the radio; the RadioPro cable cannot be used to program an APX 4500.

The APX 4500 offers no GPS functionality that the gateway can use, so data revert operation cannot be used with it.

Features available

On a P25 system through this interface, RadioPro gives voice dispatch only, and it is talk and listen with no PTT ID. Text messaging, GPS mapping, ARS, private call, remote monitor, remote enable/disable and telephone-interconnect monitoring are not available. Compare radiopro-dispatch-feature-availability-by-system-type.

ICU Intercom tab settings

Connect with ICU and open the Intercom tab.

Tx audio

  • PTT output polarity must match the radio. An active low PTT radio expects the PTT line to be high when not transmitting and pulled to ground to transmit; an active high radio expects the opposite. The APX 4500 PTT line is active low.
  • Allow transmission while receiving lets a client transmit while the radio is receiving. It should be checked only for radios that have full-duplex capability. When disabled, a client that tries to transmit during a received call gets a "bonk". The APX 4500 does not have full duplex, so the setting should be disabled.

Rx audio

  • Activity detect input must match the radio. An active low COR radio holds a high voltage on the COR line when idle and pulls it low when a transmission is received. The APX 4500 COR line is active low.
  • Enable VOX makes the gateway act as a voice-operated switch: when enabled, a receive call is detected by the activation level (in dB); when disabled, it is detected from the radio's COR signal.
  • Deactivation hangtime (ms) is how long VOX keeps the incoming audio transmission up after the last good audio level.

VOX is also the fallback when a radio's COR line is unavailable or unreliable. These Intercom tab choices (PTT polarity, COR polarity and VOX) are the same ones used for any radio connected to the gateway over plain COR/PTT, such as a generic Rx/Tx radio, so they apply beyond the APX 4500.

A "bonk" when a client transmits while the APX 4500 is receiving is therefore expected behavior, not a fault: the radio has no full duplex, and the setting is disabled.

Interface cable S2-61927

The cable has a DE-9 male connector for the gateway's female connector and a 26-pin connector for the radio's rear accessory connector. See radiopro-part-numbers-and-ordering for the other RadioPro cables.

Signal IP Gateway DE-9 pin APX 4500 accessory connector (HLN6961) pin
Digital ground 3 1 (orange)
Serial Rx / COR 1 13 (brown)
Radio mic − 5 14 (green), pinned together with 15
Radio speaker − 9 15 (black), pinned together with 14
Serial Tx / PTT 6 16 (blue)
Radio speaker + 8 21 (gray)
Radio mic + 4 23 (yellow)
12 V accessory 2 25 (red)

Installation sequence

  1. Configure the APX 4500 for voice. No RadioPro-specific radio programming is required.
  2. Disconnect the programming cable before connecting the gateway.
  3. Connect cable S2-61927: the DE-9 end to the gateway's rear DE-9 connector and the 26-pin end to the radio's rear accessory connector.
  4. Disable Wi-Fi on the PC used to configure the gateway.
  5. Configure the gateway with ICU before connecting it to the LAN. Do not connect the gateway to an IP network until its IP parameters are set.
  6. Install at least one client (radiopro-dispatch-software-overview, radiopro-solo-virtual-radio or radiopro-talk-mobile-app).

Source documents

This article summarizes the following published CTI Products manuals. They are the authoritative reference.

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.