Bridging Two Radio Systems with RadioPro: Patching a MOTOTRBO System to a NEXEDGE System

RadioPro and CTI Products · Last updated · About 4 min read

How to carry audio between two different two-way radio systems, such as Motorola MOTOTRBO and Kenwood NEXEDGE, by patching two RadioPro IP Gateways over IP.

Can audio from one radio system be sent to a different radio system, for example from a Motorola MOTOTRBO system to a Kenwood NEXEDGE system? Yes, with RadioPro patching. One RadioPro IP Gateway is installed on each system and the two gateways are patched together over IP. The control-station radios do not have to be the same brand, model or radio technology.

Why it works

A RadioPro patch is an IP audio bridge between two gateways. Each gateway has already turned its control-station radio's audio into IP audio before the patch touches it, so the patch never sees DMR, NXDN or any other air-interface detail. It simply moves audio between two IP endpoints. That is why the radio technology at each end does not matter to the patch.

What you need

Requirement Detail
Two IP Gateways One per radio system. A gateway attaches to exactly one voice control-station radio
A control-station radio on each system On the channel you want to bridge: the MOTOTRBO radio connects by USB, the NEXEDGE radio by serial (radiopro-supported-control-station-radios)
IP reachability between the gateways For a patch the two gateways communicate directly with each other, not through a client
RadioPro Dispatch, for a temporary patch A temporary patch is made from the Dispatch client (radiopro-dispatch-voice-dispatching); Solo and Talk cannot patch
ICU, for a permanent patch A permanent patch is set on ICU's Permanent Patch tab. It stays in place with no client connected

Steps

  1. Install a gateway with a MOTOTRBO control-station radio set to the channel to be bridged (radiopro-ip-gateway-with-motorola-mototrbo).
  2. Install a gateway with a NEXEDGE control-station radio set to its channel (radiopro-ip-gateway-with-kenwood-nexedge).
  3. Confirm both gateways are in the same RadioPro system and can reach each other over IP.
  4. For a temporary patch, patch the two from RadioPro Dispatch. For a permanent patch, configure it on the Permanent Patch tab in ICU.
  5. Test in both directions: transmit on each system and confirm the audio is heard on the other.

What crosses the patch, and what does not

Audio crosses the patch. Nothing else does.

Crosses Does not cross
Voice audio, in both directions GPS and location data
Text messages
Radio IDs and aliases
Emergency signaling
Telemetry
Channel steering

Those are data services that belong to each radio system and to its own control-station radio. A patch carries an audio stream, and there is no translation layer between two different radio technologies, so nothing maps a DMR radio ID onto an NXDN one. Each system keeps its own addressing.

In practice a dispatcher on the MOTOTRBO side hears the audio from the NEXEDGE side but sees nothing about who is talking: no alias, no ID and no position. If a customer expects one subscriber list or one map across both systems, a patch does not provide that.

Limits

  • Each gateway is patched to one partner gateway at a time, so patches cannot be daisy-chained to join three or more channels.
  • The limit is enforced in software, to avoid the problems that arise when too many devices are patched together.
  • Check the patching limits in the Dispatch documentation for your version before quoting a channel count to a customer (radiopro-dispatch-voice-dispatching).

Check audio levels on a mixed-brand patch

The two gateways connect to different radio families, and each radio is set up with its own audio-level settings: the MOTOTRBO guide asks for a rear microphone gain of +10 dB, while the Kenwood guide asks for a DEO level of +5 (radiopro-ip-gateway-with-motorola-mototrbo, radiopro-ip-gateway-with-kenwood-nexedge). Two paths calibrated separately can end up at different levels, so after patching, listen in both directions. If one side is louder or quieter, adjust the levels on the radio side as described in the installation guide for that radio. See audio-levels-and-radio-interfacing for the general idea.

A note on wording

CTI documents describe patching as joining two talk groups. In RadioPro, one gateway holds one control-station radio on one channel, so "talk group" in that sentence means "gateway". It does not mean two talk groups inside one radio system, and a patch does not act on DMR or NXDN talk group IDs. For the radio-system meaning of the term see talkgroups-and-fleet-mapping.

When a patch is not the right answer

Situation Better approach
Bridging more than two channels Outside the one-partner-per-gateway limit. See cross-patching-and-system-bridging for other methods
Unified IDs, GPS or subscriber lists across both systems Not possible by patching, and not a RadioPro capability
One-to-many distribution to many listeners Use a different design than a patch, for example a conferencing or relay arrangement (roip-radio-over-ip)

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.