Connecting a RadioPro IP Gateway to a MOTOTRBO Control-Station Radio
MOTOTRBO CPS settings, IP addressing rules, Enhanced GPS and Connect Plus setup for RadioPro control-station and subscriber radios.
This article summarizes how a Motorola MOTOTRBO radio is prepared as the control-station radio for a RadioPro IP Gateway, and how subscriber radios are set up so that ARS, GPS and text messaging reach RadioPro clients. General gateway steps are in radiopro-ip-gateway-installation-and-configuration. Radio background: motorola-mototrbo-overview, motorola-mototrbo-xpr-5550, motorola-mototrbo-xpr-2500 and programming-motorola-mototrbo-radios.
Required pieces
- A radio interface cable per gateway: S2-61431 for the XPR 5350, 5550 and 5550e (DE-9 for audio plus USB for data), and S2-61916 for the XPR 2500. The cable for a dedicated data revert radio is S2-61664 (USB only, since that radio carries no audio); see radiopro-data-revert-radios and radiopro-part-numbers-and-ordering. A MOTOTRBO radio connects to the gateway by USB, over its own independent IP link.
- A control-station radio at or above the minimum firmware (1.08.0 for conventional, IP Site Connect, Capacity Plus and Linked Capacity Plus; 2.2.0 for Connect Plus; 1.3.0 for the Connect Plus option board), configured with Motorola CPS (Customer Programming Software). Either the Motorola programming cable or the RadioPro gateway cable can be used with CPS.
- Warning: a programming cable on the radio's front microphone connector prevents communication through the rear accessory connector. The front and rear ports cannot be engaged at the same time. After programming, remove the cable from the front connector (and, for the XPR 2500, power-cycle the radio).
Feature support by system type is in radiopro-dispatch-feature-availability-by-system-type.
Control-station radio CPS settings (voice)
Use CPS in Expert view.
| Folder | Parameter | Setting |
|---|---|---|
| General Settings | Radio ID | The voice radio and any data revert radio sharing one gateway must have the same Radio ID |
| General Settings | GPS | Disabled (XPR 5350/5550/5550e) |
| Microphone | Analog Mic AGC, Digital Mic AGC | Unchecked |
| Persistent LRRP Requests | Save, Delete | Unchecked |
| Accessories | Ignition Sense | On/Off or Ignition |
| Accessories | Analog and Digital Rear Mic Gain | +10 dB (not needed on a data revert radio). May be adjusted slightly; the 5000-series guide warns not to go outside +9 to +11 dB, and the XPR 2500 guide gives +9 to +12 dB |
| Accessories | Cable Type | Rear PC and Audio |
| Network | Radio IP | Normally the factory default; must be on a different subnet from the gateway |
| Network | Forward to PC | Via USB (required for text messaging) |
| Network | ARS Radio ID, TMS Radio ID | Blank |
| Signaling Systems | MDC, Digital or Capacity Plus | Add a system if a client will send an emergency indication |
| Contacts | Group Call and All Call | Add a Group Call with the group ID (needed for group calls) and an All Call (needed for All-Call from Dispatch) |
| Channels (digital) | ARS | Unchecked (disabled) |
| Channels (digital) | Compressed UDP Data Header | MSI |
| Channels | Emergency System / Signaling System in the TX section | Set for the All-Emergency function |
| Channels (digital, TX) | Data Call Confirmed | Unchecked |
| Channels | Enhanced GPS | Enabled only on a data revert radio when the repeater has the option; unchecked on a voice radio |
| Channels | RX Only | Checked for a radio used only to collect GPS from a data revert slot |
The XPR 2500 offers no GPS, so data revert operation cannot be used with that model.
Rules for radios sharing one gateway
- All radios sharing a gateway must have the same Radio ID.
- All radios sharing a gateway must be on different IP subnets.
- The IP address of the voice radio must be lower than the IP addresses of the GPS data revert radio(s).
IP addressing example
If the subnet mask is 255.255.255.0, at least one of the first three octets of the radio's IP address must differ from the gateway's. A radio at 192.168.12.2 and a gateway at 192.168.12.3 are on the same subnet and are not valid; a radio at 192.168.12.2 and a gateway at 192.168.10.3 are valid. See networking-ipv4 and radiopro-system-planning-for-mototrbo.
Connect Plus
For a Connect Plus control station, CPS is used to configure the radio for one digital channel; the Connect Plus option board carries the talk groups ("zones"), and cannot pass them out the rear connector. To let a RadioPro client select talk groups, add as many generic channels (Channel1, Channel2 and so on) as there are zones in the option board, and enable both Option Board and Option Board Trunking on each. The ICU Zones/Channels tab shows the names clients will see; channels can be renamed or hidden (Visible unchecked). The option board needs these menu items enabled: Call Alert, Manual Dial, Radio Check, Remote Monitor, Radio Enable and Radio Disable, and the call log items Missed, Answered and Outgoing. Subscriber ARS, GPS and TMS configuration is not needed (and not available) for Connect Plus through a control station.
Subscriber radio settings for ARS, GPS and text
Needed only if ARS, GPS or text messaging is wanted at the client.
| Folder | Parameter | Setting |
|---|---|---|
| General Settings | GNSS (GPS) | Checked |
| Persistent LRRP Requests | Save, Delete | Unchecked |
| Network | ARS Radio ID and TMS Radio ID | The Radio ID of the control-station radio connected to the gateway |
| Channels (digital used for GPS) | Scan/Roam List | None (ARS and GPS will not work if scan is enabled) |
| Channels | ARS | On System Change |
| Channels | Compressed UDP Data Header | MSI |
| Channels (TX) | GPS Revert | "Selected" if there is no data revert slot, otherwise the data revert channel name |
| Channels | Data Call Confirmed | Unchecked (if greyed out, make sure Enhanced GPS is unchecked) |
See ars-automatic-registration-service and mototrbo-data-services.
Enhanced GPS and data revert
If Dispatch maps GPS for more than 25 radios per repeater slot, dedicating one or more data revert slots to GPS is recommended, and the repeater should have the Enhanced GPS option enabled. In the System Planner's comparison, updating 225 radios once a minute with 100% reliability takes 12 data revert slots on 6 repeaters without Enhanced GPS and 2 slots on 1 repeater with it. One gateway supports one voice radio and up to three data revert radios (gateway software 5.1.5 or later). More on counts, capacity tables and cables is in radiopro-data-revert-radios. The Window Size is system-wide: it must be set to the same value in the repeater, the data revert radios and the subscribers. Use 5 when Privacy Type is None and 6 when Privacy Type is Enhanced. For Basic privacy this guide says 6, while the RadioPro System Planner lists Basic under window size 5, so confirm with CTI Products before deploying. The guide's tables give the number of radio GPS updates for a window reservation, for example with window size 5 and a 90% reservation, a 30-second update interval supports 90 radios and a one-minute interval supports 180. With window size 6 the figures at 90% are 74 and 148.
ICU settings for MOTOTRBO
- Mototrbo Radio tab: the ARS Subscriber Refresh Rate (default 0.5 hours). Other values match the radio defaults and normally should not be changed.
- Zones/Channels Aliases tab: downloaded from the connected radio and shown in Dispatch's radio controller; names can be edited while the radio is connected and powered. In Capacity Plus systems the radio adds a zone named Channel Pool, which is usually hidden from dispatchers.
- GPS tab: check Enable GPS Updates only if mapping is needed, because it increases radio transmissions. The Minimum Poll Rate sets the minimum time between GPS updates; raising it frees channel bandwidth for voice.
Source documents
This article summarizes the following published CTI Products manuals. They are the authoritative reference.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.