RadioPro Data Revert Radios: Adding GPS and Data Capacity to a MOTOTRBO or NEXEDGE System

RadioPro and CTI Products · Last updated · About 5 min read

How a dedicated data revert radio behind a RadioPro IP Gateway carries GPS and ARS traffic, with radio counts, configuration rules, Enhanced GPS capacity and cable part numbers.

Data revert is a MOTOTRBO or NEXEDGE configuration in which a separate, dedicated control-station radio handles GPS and data traffic, apart from the main voice control-station radio. It is how a RadioPro system scales up the amount of GPS, ARS and other data it can carry on a talk group. For the general idea of a GPS revert channel see mototrbo-data-services.

Why a separate data radio

On a single conventional or IP Site Connect channel, voice and data (GPS location updates, ARS registrations and text messages) compete for the same limited over-the-air capacity. A data revert radio is a second control-station radio behind the same gateway that is dedicated to receiving data. It lets a system carry far more GPS update traffic without crowding out voice.

How many data revert radios a gateway supports

Radio system Data revert radios per gateway How they connect
Motorola MOTOTRBO Up to 3, in addition to the voice radio USB, like the voice radio. The gateway has four USB ports on the back, enough for one voice radio and three data revert radios without a USB hub
Kenwood NEXEDGE 1 A serial port on the back of the gateway, a different connector from the one used for the NEXEDGE voice interface

For MOTOTRBO, one gateway supports one voice control-station radio and three data revert radios, and the gateway software must be version 5.1.5 or later (radiopro-system-planning-for-mototrbo). The XPR 2500 has no GPS, so it cannot be used as a data revert radio, and the APX 4500 offers no GPS that the gateway can use (radiopro-supported-control-station-radios).

Configuration rules

These rules for a voice radio and data revert radios that share one gateway are the ones most often missed (radiopro-ip-gateway-with-motorola-mototrbo):

  • Same Radio ID. The voice radio and the data revert radios sharing a gateway must be programmed with the same Radio ID.
  • Different subnets, voice radio lower. The gateway and every radio connected to it must each be on their own subnet, and the voice radio's IP address must be lower than the data revert radios' addresses.
  • Microphone gain is for the voice radio only. The rear microphone gain (+10 dB) is not needed on a data revert radio, because it carries no voice.
  • Signaling and contacts on the voice radio only. The signaling system and the Group Call contacts used for group calls and the All-Emergency function are configured on the voice radio, not on the data revert radio.
  • RX Only for a GPS-only radio. A radio that only collects GPS from a data revert repeater slot can be set to RX Only.
  • Enhanced GPS. If the data revert radio works with a repeater that has Motorola's Enhanced GPS option, the data revert radio and its repeater must use the same Enhanced GPS settings, described below.

For NEXEDGE, the data revert radio is configured like the voice radio except that the sound options and the data settings are skipped, the GPS settings are required, and only the data channel is programmed (radiopro-ip-gateway-with-kenwood-nexedge). Subscriber radios must then point their GPS reports at the data revert radio's ID rather than the voice radio's.

Enhanced GPS: why it matters at scale

Motorola's Enhanced GPS repeater option divides the update interval into "time slices". When a subscriber radio powers on, the repeater synchronizes with it and assigns it a unique slice, and the radio reports GPS only when its slice recurs, which eliminates collisions. The RadioPro System Planner compares two systems that each must update 225 subscriber radios once a minute with 100% reliability:

Enhanced GPS option Data revert repeater slots needed Data revert repeaters needed
No 12 6
Yes 2 1

The guides recommend dedicating one or more data revert slots, with Enhanced GPS enabled on the repeater, once RadioPro Dispatch will map more than 25 radios per repeater slot. Below that, a shared slot is generally enough.

Window Size

Enhanced GPS uses a Window Size setting. It is system-wide: the same value must be set in the repeater, the data revert radios and the subscriber radios, or GPS updates fail. Use 5 when the Privacy Type is None and 6 when it is Enhanced. For Basic privacy the installation guide says 6 while the System Planner lists Basic under window size 5, so confirm with CTI Products before deploying.

How many radios one repeater slot can serve depends on the window size, the window reservation and the GPS update interval. At the recommended 90% window reservation:

Update interval Window Size 5 Window Size 6
30 seconds 90 radios 74 radios
1 minute 180 148
2 minutes 360 296
4 minutes 720 592
8 minutes 1440 1184

Lower window reservations (75, 60 and 45%) serve proportionally fewer radios; the System Planner has the complete tables. A longer update interval serves more radios per slot but updates positions less often. When Enhanced GPS is used, the gateway's minimum GPS poll rate in ICU must be 30, 60, 120, 240 or 480 seconds, which are the only values the option supports.

ARS and GPS settings in ICU

  • The ARS Subscriber Refresh Rate on the ICU MOTOTRBO Radio tab sets how often subscribers re-register. Its default is 0.5 hours.
  • Enable GPS Updates and the Minimum Poll Rate on the GPS tab set how often subscriber positions are requested. Raising the poll rate reduces GPS traffic and frees channel bandwidth for voice.
  • Which slot or channel carries each type of data message depends on the radio system type: conventional, IP Site Connect, Capacity Plus or Linked Capacity Plus. For Capacity Plus and Linked Capacity Plus, the repeaters used for data revert are stand-alone and are not part of the trunked system.

Cables

A data revert cable has no audio lines, since the data radio carries no audio, and it is different from the voice interface cable. The Motorola MOTOTRBO data revert cable is S2-61664 (USB only). Kenwood NEXEDGE data revert cables are 89-10505 and S2-61891, depending on the radio. All part numbers are listed in radiopro-part-numbers-and-ordering.

Source documents

This article summarizes the following published CTI Products manuals. They are the authoritative reference.

This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.

Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.