Planning a RadioPro System for MOTOTRBO: Gateways, Data Revert, ARS and GPS
How many IP Gateways and control-station radios a RadioPro system needs on conventional, IP Site Connect and Capacity Plus MOTOTRBO systems.
The RadioPro System Planner is a design guide for adding RadioPro to a MOTOTRBO system. This article summarizes its rules. The gateway and radio settings themselves are in radiopro-ip-gateway-with-motorola-mototrbo, and the product background is in radiopro-ip-gateway-overview. For general system design see designing-a-two-way-radio-system.
Basic sizing rules
- One IP Gateway and one control-station radio per voice channel or talk group that must be used at the same time. Simultaneous monitoring of several channels needs one control-station radio per channel.
- Each gateway needs a static IP address, and each gateway and every radio connected to it must be on its own subnet.
- Limits tested by CTI: 80 clients per gateway, 70 gateways per Dispatch client.
- A functional system has at least one gateway, one client, Ethernet access between them, and a connection license for each Dispatch or Solo client (radiopro-dispatch-layout-gateways-and-licensing).
- The planner includes a template for recording IP addresses, user names, passwords, serial numbers and device names for the gateways, the Dispatch clients and the Solo and Talk clients.
Control-station radios, cables and software
Compatible control-station models are the Motorola MOTOTRBO XPR 2500 and XPR 5550/5550e, the Motorola APX 4500 (intercom only), and Kenwood NX-700/800, NX-720/820, NX-3720/3820 and NX-5700/5800 (radiopro-supported-control-station-radios). A cable specific to the radio model is needed for each gateway. Radios are configured with Motorola CPS or Kenwood FPU software, and a laptop or PC is needed to run ICU.
Installation sequence
- Configure the control-station radios for voice, and for data if data revert is used.
- Configure the Connect Plus option board, if applicable.
- Configure subscriber radios for ARS, GPS and text messaging.
- Configure the repeaters for the Enhanced GPS option, if used.
- Connect each gateway to its control-station radio.
- Configure radio-specific, then remaining, gateway settings in ICU (radiopro-ip-gateway-installation-and-configuration).
- Connect the gateway to the IP network and configure port forwarding.
- Install the clients (radiopro-solo-virtual-radio, radiopro-dispatch-software-overview, radiopro-talk-mobile-app).
ARS signaling
Applications such as RadioPro need to know which subscriber radios are active. Subscribers send periodic ARS (Automatic Registration Service) status messages to an ARS server. If the radio gets no acknowledgement it keeps resending, which can flood the channel with data. The RadioPro IP Gateway performs the ARS server function and acknowledges each message. The acknowledgement carries the ARS Subscriber Refresh Rate, which tells radios how often to resend; it is set in the MOTOTRBO Radio tab of ICU. See ars-automatic-registration-service.
GPS signaling
The gateway sends an LRRP (Location Request Response Protocol) request and the target subscriber answers with its position, possibly with speed, time and other parameters. A request can be an immediate location request, answered with a single position message, or a triggered location request, answered with periodic updates on a time interval or an event such as radio key-up. The triggered-request parameters are in the GPS tab of ICU. See mototrbo-data-services and gps-global-positioning-system.
Topologies
| System | What the planner says |
|---|---|
| Conventional digital or analog, without data revert; or Connect Plus (voice only) | Each repeater voice slot needs its own control-station radio (the examples use an XPR 5550) and gateway. All ARS and GPS requests and status messages use the same voice slot and channel. |
| Conventional digital with data revert | One gateway can support one voice radio plus up to three data revert radios (gateway software 5.1.5 or later). Only the subscriber GPS status messages use the data revert slot; GPS requests, ARS status and ARS acknowledgements use the voice radio and voice slot. |
| IP Site Connect without data revert | One gateway and control station for each local (non-IP Site Connect) slot, plus one for each wide-area IP Site Connect "channel". The wide-area gateway and radio can be at any site. |
| IP Site Connect with data revert | As above with data revert; a GPS request goes out on the voice radio and slot and the subscriber's GPS status comes back on a data revert slot and data radio, as does the ARS status, while the ARS acknowledgement uses the voice side. |
| Capacity Plus without data revert | Several gateway and control-station pairs can share a smaller number of trunked repeater slots. GPS request and response use the same voice slot, while ARS status and acknowledgement use the Rest slot on the same voice channel. |
| Capacity Plus with data revert | As above with data revert: gateway messages use a trunked voice slot; subscriber GPS and ARS status messages use a data revert slot. |
Rules for radios that share a gateway: all must have the same Radio ID; all must be on different subnets; and the voice radio's IP address must be lower than the data revert radios'. See ip-site-connect, mototrbo-capacity-plus and mototrbo-linked-capacity-plus.
Motorola Enhanced GPS repeater option
The Enhanced GPS option for MOTOTRBO repeaters improves GPS throughput on data revert slots. It splits the update interval (30 seconds, 1, 2, 4 or 8 minutes) into time slices: when a subscriber powers on, the repeater synchronizes its clock with the radio and assigns the radio a unique time slice, so the radio reports when its slice recurs and data collisions are eliminated. The planner's example: updating 225 subscribers once a minute with 100% data reliability needs 12 data revert slots (6 repeaters) without the option and 2 slots (1 repeater) with it.
Requirements: gateways and repeaters must be configured for it, with the same Window Size at every radio and repeater, and the subscriber radios must have the Enhanced GPS parameter set (radiopro-ip-gateway-with-motorola-mototrbo). The option is licensed from Motorola, for new or existing repeaters.
Other planning notes
- A section of the planner covers port forwarding on routers, rack mounting (a 2RU shelf of at least 12 inches depth, with the XPR 5550 mountable alongside) and system compatibility. See port-forwarding-and-remote-access.
- Design resources named in the planner include Motorola's MOTOTRBO system design tools.
Source documents
This article summarizes the following published CTI Products manuals. They are the authoritative reference.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.