RadioPro Solo: A Virtual Control-Station Radio on a Windows PC
RadioPro Solo puts a virtual control-station radio on a Windows PC: Intercom, private calls, menus, installation and licensing.
RadioPro Solo is a Windows application that puts a virtual radio on the desktop and connects it to one MOTOTRBO or NEXEDGE control-station radio through a RadioPro IP Gateway. The data sheet's tagline is "simplicity that users expect, functionality that radio administrators require". It provides talk and listen from any Windows PC, group and private calls, text messaging, cross-muting, voice and event logging for the previous 24 hours, and full radio control including channel steering and scan settings. Supported PTT accessories include desktop microphones, headsets, footswitches and touch screens (radiopro-microphones-and-ptt-accessories). Solo is the single-radio counterpart of RadioPro Dispatch; see radiopro-product-family-and-client-comparison.
When to use it
- Simultaneous radio sharing. A base-station radio used to be shared with speaker boxes, microphones, PTT switches and audio junction boxes, with wiring to every workstation and little functionality beyond push-to-talk and listen. With Solo each user runs the client on an existing PC; any IP connection (LAN, WAN or Internet) carries audio and data, and the user also gets the radio's other functions. The data sheet calls it a low-cost, easy-to-implement alternative to tone remotes.
- Remote access outside coverage. Underground or building areas where radio does not work, a home office or satellite office outside the coverage area, or travel, as long as an IP connection exists.
- Supervisory or centralized monitoring of radio channels, and offices where a real radio would be too expensive, need too much hardware, or cause RF problems.
The virtual radio
The Solo window is a virtual front panel of the control-station radio: all radio functions and buttons are operational except the Power button and the volume knob (the Volume slider replaces it). Permanent power-off is not possible, but the radio can be power-cycled with Reboot Radio. Other elements:
- Push to Talk. Works like the PTT on a portable radio or hand microphone. The PTT acknowledgement tone must be heard before speaking, or the start of the message will not be transmitted. With "Default" in the Recipient box, a transmission goes to the default group programmed in the base station radio.
- Recipient list. For private or group calls, open the Recipient list and pick a subscriber or group. A green icon means the subscriber was detected by the radio's ARS and is considered available; a red icon means it was not detected (ars-automatic-registration-service).
- Call Alert sends an alert tone to a subscriber in the list.
- Intercom is like PTT but reaches only other Solo clients connected to the same gateway. It is not transmitted to any radio, so it uses no radio-system bandwidth, and it is duplex: several clients can speak and listen at the same time.
- Replay repeats the last audio, and access is provided to audio and events from the previous 24 hours.
- Global volume and microphone sliders at the bottom right mute incoming or outgoing audio when moved fully down.
Menus
| Menu | Contents |
|---|---|
| File | Disconnect from the gateway, Exit |
| Radio | Permanent Monitor, Scan on/off, high/low Power (only for radios with power levels and when programmed), Reboot Radio, Emergency TX (if enabled in the radio) |
| Channel | Select a zone (up to 16 channels per zone) |
| View | Active Users (user name and IP address), Text Messaging and Quick Text (text works only with radios in digital mode), Recent History (last 50 transmissions), Browse History (up to the last 50 transmissions from a chosen time in the past 24 hours) |
| Settings | Change password; Client options (always on top, minimize to tray, come to front on a call or hotkey, set the private call recipient to the last received call, clear texts, mark users unavailable after inactivity); Gateway aliases (names for gateway addresses used at login); Audio (devices, quality, PC cross-mute); Quick Text; About |
| Help | About, Remote Support, Logs |
An administrator login also gets a Gateway submenu to edit accounts, edit radio aliases (with import and export), view gateway information and reboot the gateway, and Update License.
Audio quality
| High quality | Compressed | |
|---|---|---|
| Bandwidth per voice stream (one talk group) | 22 kBytes/s | 2.2 kBytes/s |
| For 10 voice streams | 220 kBytes/s | 22 kBytes/s |
| Best for | Highest audio quality between radios and clients | Most efficient use of network bandwidth |
PC cross-mute helps when several PCs are in one room: PCs with the same Cross Mute ID do not play back each other's audio.
Installing and connecting
- PC: Windows 10 (the older guide allows Windows 8.1), a network interface of 10 Mbps or faster, speakers or headphones, and a microphone. A USB external microphone is recommended (an analog external microphone also works); the built-in microphone is not recommended. See radiopro-microphones-and-ptt-accessories.
- Solo is compatible with version 9 IP Gateways (and, per the compatibility table, version 8 gateways). Installation of Solo may not be needed at all if other client types are already deployed. It can be installed on as many PCs as needed.
- Download it from the RadioPro upgrade downloads page or take it from the distribution USB drive. Run the installer; a desktop icon is created.
- On first run, enter the gateway's IP address (and port if it is not the default 48222) and a user name and password. If the Solo PC is outside your LAN, the IT administrator must set up port forwarding in the firewall or router and the address is entered as
address:port(radiopro-ip-gateway-installation-and-configuration). Aliases for these addresses can be created in Settings. - The status bar then shows the user ID and the connection status of the gateway and the radio.
Behavior notes
- One gateway at a time. Unlike Dispatch, which connects to many gateways at once, Solo connects to a single gateway. Since every client on a gateway follows its radio's selected channel, Solo works one channel at a time, like the physical radio it imitates.
- The 24-hour history lives in the gateway. The previous 24 hours of audio and events are stored in the IP Gateway, not in the Solo client, and the 24-hour window is fixed. Solo and Talk both have a playback function that retrieves this gateway-side audio.
- Installs versus connections. Solo can be installed on as many PCs as needed. The number of simultaneous connections is capped by the gateway's Solo and Talk license, not by the number of installs.
- PC cross-mute. The cross-mute feature is a setting in Solo's Settings, Client, Audio tab: enable PC Cross Mute and give nearby PCs the same Cross Mute ID. The ID is set in the client rather than the gateway, so the PCs do not need to share a gateway. This stops the same received audio playing from several computers in one room.
- Supported platforms. Solo and Dispatch are designed for Windows 10 or 11 Professional. They are not designed for Windows Server editions, and running them on a virtual desktop may work but is not a documented configuration.
Licensing
Solo licenses are held in the gateway, not the PC. A connection beyond the licensed number is limited to 5 minutes. To increase the number, the administrator uses Update License to get the license key file from the gateway, sends it to CTI Products, and sets the returned file back on the gateway. See radiopro-ip-gateway-overview.
Feature availability
Group and private call, voice recording, text messaging, ARS (radio availability) and full radio control depend on the radio system type, in the same way as for Dispatch. See radiopro-dispatch-feature-availability-by-system-type.
Source documents
This article summarizes the following published CTI Products manuals. They are the authoritative reference.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.