RadioPro Dispatch Installation, Layout, Gateway List and Licensing
PC requirements, installation, license import, gateway list with failover, layouts, audio presets and settings for RadioPro Dispatch.
This article summarizes how a RadioPro Dispatch console PC is prepared and configured. The planning step that comes first is in radiopro-system-planning-for-mototrbo, and the gateways must be installed before the client (radiopro-ip-gateway-installation-and-configuration).
System limits
The RadioPro solution was tested and verified up to 80 clients per IP Gateway and 70 IP Gateways per Dispatch client. Each IP Gateway needs a static IP address and serves one control-station radio, so there is no server PC and no single point of failure in the middle.
Console PC requirements
| Item | Requirement |
|---|---|
| Processor | Intel Core i5 or better |
| Operating system | Windows 10 Pro recommended; the Dispatch client must run as administrator |
| Memory | 8 GBytes recommended, 4 GBytes minimum |
| First disk | 160 GBytes minimum, for the operating system |
| Second disk or partition | 2 TBytes recommended (500 GBytes minimum) for voice and event logging; not the C: partition |
| Network | 10 Mbps or faster; up to 22 kBytes/s per connected IP Gateway |
| Monitors | Dual recommended if voice dispatch and GPS mapping are both used; 20 inch minimum, 23 inch recommended |
| Audio | Headset (USB, analog or Bluetooth) or desk microphone and stereo speakers |
| Software | .NET 4.0 or higher |
PC settings: set power options so the PC never sleeps or hibernates; for each USB root hub, disable "allow the computer to turn off this device to save power"; keep the display at normal font size and 96 DPI; if a touch screen is used, disable the Windows touch parameters because Dispatch interprets touches as game-controller events.
Things that must match
- Version match: a Dispatch client and its IP Gateways are compatible when the first two digits of the version match; the third digit is a minor revision. The client license must be for the same major version, so a version 8 license will not run version 9.
- Time: all gateways should use the same NTP time server so that logged events carry accurate times. The server can be an existing LAN time server, a public one, or one on a common PC such as the console. See ntp-network-time-protocol.
- Control-station firmware: see radiopro-dispatch-feature-availability-by-system-type.
Installing
- Install and configure the IP Gateways first, using the ICU (IP Configuration Utility), and configure each control-station radio with the manufacturer's tool.
- Connect and let Windows install drivers for microphones, speakers, headsets and PTT devices.
- Run the client installer from the distribution USB drive and set "Run as administrator".
- Start the client and import the license file from the license USB drive. Each console PC needs its own license file, which sets the number of gateway connections and enables the Voice, GPS, Text and Telemetry modules. Connections and modules can be added later. If an import fails with an error, restart Dispatch as administrator and repeat. A timed license can be converted to a non-expiring one.
Configuring
Configuration is possible only in Edit mode (File, Edit; File, Lock returns to Run mode). The steps are:
- Administrator password. Choose File, Save As to save a layout; a Password Protect File window lets you set the administrator password. A User cannot change the configuration; an Administrator can.
- Manage IP Gateways (Options menu). Add each gateway by IP address and port. The default port is TCP 48222 and can be changed with the ICU. If the gateway is on another subnet behind a firewall or router, enter the firewall's external address and set up a port-forward for each gateway. Enter the gateway password and use Test ("Connection Successful"). An optional secondary address gives gateway failover: Auto uses the primary unless it is down, Primary forces the primary, Secondary forces the secondary. The status table shows address, name, gateway status and firmware, radio firmware, Pri/Sec, date and time, and the Record, Audio and Text options.
- Audio presets, described below.
- Choose and arrange panels: Subscribers, Recent History, Messages, Geo-fence Alerts, Telemetry and Missed Calls.
- Add tabs for Voice and GPS maps, and add Radio Controllers to a voice tab for each talk group or channel.
- Add subscribers and groups (radiopro-dispatch-subscribers-contacts-and-messaging).
- Other Dispatch options, below.
- Save the layout. Save As creates a
.xmland a.tdcfglayout file; these can be copied to other PCs but should not be edited by hand.
Cloning a configured console
On a configured PC choose File, Clone Settings (Edit mode) to write a .trbodat file; on the new PC use File, Import Cloned Settings, then import that PC's own license file and Lock. Cloning is available from Dispatch 7.0.5.
Audio configuration
- General: Mute Audio When Transmitting (prevents feedback); Enable PC Cross Mute (consoles with the same cross-mute ID cannot hear each other); Audio Quality.
- Audio quality: Compressed mode uses 2.2 kBytes/s per client user and talk group and should be used over a WAN such as the Internet or where bandwidth is a concern. High Quality uses 22 kBytes/s and gives about 10% better audio when neither condition applies.
- Presets / Devices: a named preset selects Mic In, Select Out, Unselect Out and Intercom Out (each Both, Left or Right speaker).
- Levels: starting levels: Mic and Select 100%, Unselect 60%, Intercom 60%, alert sounds ("Talk-Permit", "Channel-Busy") 30%. If audio heard on portable and mobile radios is not loud enough, adjust the Rear Mic Gain in the control-station radios.
- Advanced: rules for duplicate PTT ID audio and Intercom levels.
A separate guide covers USB microphones with PTT buttons: the Microphone Audio and PTT Configuration guide, with its patch for Dispatch 8.3.22 and 9.3.12 and later (radiopro-microphones-and-ptt-accessories).
Dispatch Settings folders
| Folder | Purpose |
|---|---|
| General | Lock Select/Unselect, hide window buttons when locked, number of recent history items (1 to 500), PTT debounce time (typical 200 ms), replace analog call aliases with the gateway name, touch-screen options |
| Dispatch Users | Names that appear as the user in history; optionally use the Windows login |
| Subscriber List | Show "All" group, unavailable timer, which action buttons to show |
| Missed Call List | Rules for the missed calls panel |
| History Logging | Storage (radiopro-dispatch-history-logging-and-archive-viewer) |
| Internet Proxy | Custom proxy for map services behind a LAN proxy |
| Emergencies | Transmit emergency timeout; whether clearing an emergency also reboots the radio; who gets e-mail and text notifications |
| E-Mail & Text Alerts | SMTP server and contact groups for geo-fence violations and emergencies |
| Actions | Custom actions: audio calls (All Call, Call Selected, tone alert before), text (free-form or canned), transmit emergency, telemetry, P buttons, Radio Check, GPS Update, Report Problem |
| Toolbar Buttons | Attach actions to buttons; show or hide the clock, volume sliders, Quick Map, Archive and Reports |
| USB Devices | Attach actions to USB PTT devices |
| Map view presets, overlays and geo-fences | radiopro-dispatch-gps-mapping-and-geo-fences |
Diagnostics
Help, ARS/GPS Events shows the ARS (subscriber status) and GPS messages arriving at a gateway from the radio system. See radiopro-dispatch-troubleshooting.
Source documents
This article summarizes the following published CTI Products manuals. They are the authoritative reference.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.