RSSI (Received Signal Strength Indicator)
RSSI Is Not Actually Standardized
A detail that catches people off guard: in the original IEEE 802.11 (Wi-Fi) specification, RSSI is explicitly defined as an arbitrary, vendor-specific integer — the standard sets no required relationship between the reported RSSI number and an actual dBm power value. Different chipset vendors have historically used different scales (some 0–60, some 0–100, some 0–255, sometimes called "asu" — arbitrary signal units), each with its own vendor-defined maximum and its own internal conversion to real dBm. Two devices from different manufacturers reporting "RSSI 70" are not necessarily seeing the same actual signal power. Land mobile radio and service-monitor equipment generally reports RSSI directly in dBm rather than an arbitrary vendor scale, but the same underlying caveat about cross-manufacturer comparability still applies: exact calibration, measurement bandwidth, and reported accuracy can differ between radio models, so a reading from one radio/manufacturer isn't automatically an apples-to-apples match to the same reading from a different one.
An Important Caveat: Strength Isn't the Same as Quality
More importantly for LMR use, a strong RSSI reading does not guarantee good audio quality: a signal can be strong but still noisy or distorted (for example, due to interference or multipath). This is precisely why comparators in a voting receiver system don't rely on RSSI alone — they combine it with other metrics like out-of-band noise (OOBN), using RSSI mainly once a signal is already known to be reasonably clean, and using noise-based metrics to catch cases where a strong-but-dirty signal would otherwise be mistakenly favored. The same "strength ≠ quality" point holds for digital radio: a channel can show adequate RSSI while Bit Error Rate (BER) is high enough to produce audible artifacts or dropouts, because RSSI measures raw received power, not the actual decodability of the signal on top of that power (which also depends on noise, interference, and multipath distorting the waveform itself).
Other Uses in Two-Way Radio Systems
- MOTOTRBO roaming — a subscriber radio continuously measures its current site's RSSI and compares it against a configured roam RSSI threshold, switching to a stronger available site once its current site's signal drops below that threshold. See MOTOTRBO Roaming for the full roam-list/beacon/threshold mechanics and common misconfiguration symptoms (radios that never roam, or that "ping-pong" between sites).
- Signal-strength bars on a radio's display are typically a coarse, bucketed representation of underlying RSSI (e.g., mapping a continuous dBm range down to 3-5 discrete bars), not a literal readout of the dBm value — don't assume "full bars" and "one bar" from two different radio models represent the same actual signal strength, for the same cross-manufacturer-calibration reason noted above.
- Coverage verification and drive testing use RSSI (often logged continuously against GPS position) to map real-world coverage against a system's predicted link budget — but, consistent with the caveat above, a thorough coverage study checks actual audio quality/BER at the edges of coverage, not RSSI alone, since a location can show acceptable RSSI while still being unusable due to interference or multipath.
Common Misunderstandings
- "RSSI is a universal, standardized measurement" — as covered above, it is not, particularly outside of dedicated LMR test equipment; comparing RSSI numbers across different products/vendors without knowing their calibration basis can be misleading.
- "Strong RSSI means the call will sound good" — not necessarily; see the BER and comparator-voting discussion above. Strength and cleanliness/decodability are separate properties of a received signal.
- "RSSI tells you why a signal is weak" — it only tells you that it's weak, not why (distance, terrain shadowing, interference, or receiver desensitization from a co-located transmitter can all produce the same low RSSI reading with very different fixes).
Related Pages
- Comparators
- Voting Receivers and Comparators
- Electronics Fundamentals: Decibels
- MOTOTRBO Roaming
- Troubleshooting Two-Way Radios
References
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.