Digital Access Codes: Color Code, RAN, and NAC
The Analog Ancestor: CTCSS and DCS
On analog FM channels, CTCSS (Continuous Tone-Coded Squelch System, Motorola's "PL" or Private Line) adds a continuous sub-audible tone to a transmission, and DCS (Digital-Coded Squelch, Motorola's "DPL") adds a continuous sub-audible digital code. A receiver programmed for tone squelch stays muted unless the incoming signal carries the expected tone or code, and a repeater configured with an input tone ignores signals without it. Digital standards replace the tone with a code field inside the digital data stream, but the purpose — and the failure symptoms when it is set wrong — are identical.
DMR: Color Code
DMR (Digital Mobile Radio — see DMR Digital Mobile Radio) uses a Color Code (CC) with a value from 0 to 15. Despite the name, nothing is colored; it is simply a 4-bit number carried in every burst. A radio's Color Code must match the repeater's, or the repeater will not repeat the transmission and the radio will not unmute to the repeater's output. Because there are only 16 values, Color Codes are not a security feature — just traffic separation for co-channel systems.
NXDN: RAN
NXDN (the FDMA digital standard behind Kenwood NEXEDGE and Icom IDAS — see NXDN Digital Standard) uses the RAN (Radio Access Number), a small numeric code (a 6-bit field, giving values from 0 to 63, with a "none/open" setting typically available). As with Color Code, radio and repeater RANs must agree, and receivers use RAN to stay muted to foreign traffic on a shared channel.
P25: NAC
- $F7E — a receiver programmed with this value opens on any NAC ("receive any").
- $F7F — a repeater programmed with this value repeats any incoming NAC ("repeat any"), retransmitting the received NAC.
The much larger code space (4,096 vs 16) makes NAC collisions between neighboring systems less likely than Color Code collisions, but the mechanism is otherwise the same idea.
Summary Table
| Standard | Code name | Range / size | Notes |
|---|---|---|---|
| Analog FM | CTCSS tone / DCS code | Dozens of standard tones; 100+ DCS codes | Sub-audible; analog ancestor of the digital codes |
| DMR | Color Code (CC) | 0–15 | Must match repeater; also set per timeslot channel |
| NXDN | RAN (Radio Access Number) | 0–63 | NXDN's digital squelch code |
Mismatch Symptoms
Access-code mismatches all present the same way, regardless of standard:
- Radio transmits but the repeater ignores it — the transmit indicator lights, the signal is strong on a service monitor, but the repeater never keys. The repeater is rejecting the wrong input code.
- Signal present but no audio — the receiving radio shows RF activity (busy indicator or RSSI) but stays muted, because the incoming code does not match what the receiver expects.
- One-way communication — works in one direction only, when one side's transmit code matches but the other's does not.
Because these symptoms mimic coverage or hardware problems, checking Color Code/RAN/NAC (and, on analog channels, CTCSS/DCS) early in troubleshooting saves time — see Troubleshooting Two-Way Radios. Note that matching the access code is necessary but not sufficient on digital systems: talkgroup and ID configuration must also line up (see Talkgroups and Fleet Mapping).
Related Pages
- PL Tones, CTCSS and DCS
- DMR (Digital Mobile Radio)
- NXDN Digital Standard
- P25 Project 25
- Troubleshooting Two-Way Radios
- Squelch Types
References
- Understanding Color Codes on DMR Digital Two Way Radios — Color Code values 0–15 (16 options), and unlike analog PL/DCS a color code is mandatory for DMR to function at all.
- Understanding RAN Codes in NXDN Digital Radios — NXDN RAN values 0–63 (64 options).
All code ranges and the P25 special values verified against the above sources, August 2026.
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.