Squelch Types
This page is a dedicated look at squelch mechanisms, distinct from PL Tones, CTCSS & DCS, which covers the tone systems used to implement two of the squelch types below.
What Squelch Does
Squelch is the circuit that mutes a receiver's audio output when no signal (or no wanted signal) is present, so a user hears silence between transmissions instead of continuous background noise/static.
Carrier Squelch
The simplest form: the squelch opens for any signal strong enough to be detected on the channel, regardless of its source — including co-channel users, distant interference, or skip propagation. It provides no filtering of who's on the channel, only whether anyone is transmitting.
How a Basic (Noise-Operated) Squelch Actually Decides
"Carrier squelch" is sometimes described loosely as "detecting a carrier," but classic analog FM squelch circuits actually work by measuring noise, not the carrier itself: an FM receiver's discriminator (demodulator) produces a lot of high-frequency white noise, well above the voice-audio passband, whenever no signal (or a very weak one) is being received. As soon as a signal strong enough to "capture" the receiver arrives, that above-audio-band noise drops sharply — even before the demodulated voice audio itself is fully intelligible — and the squelch circuit uses that noise drop as its trigger to open. This is why the technique is often called noise squelch or noise-operated squelch, and why the squelch circuit specifically looks at a frequency band above the voice passband rather than at the voice-band energy itself (looking at the voice band directly would cause the squelch to re-close every time the talker paused, which is exactly the chattering behavior a good squelch circuit is designed to avoid). This is the same out-of-band noise (OOBN) concept already used as a voting-quality metric on the Comparators page — a comparator quality-scores each candidate receiver's copy of a signal using essentially the same noise-based principle a basic squelch circuit uses just to decide open-vs-closed.
Squelch Level (Threshold) and Its Tradeoffs
Carrier/noise squelch is not a fixed on/off point — it has an adjustable threshold (the "squelch level," "squelch knob," or its programmed equivalent in a digital radio's codeplug) setting how strong a signal (or how low the discriminator noise) must be before the squelch opens:
- Set too tight (high threshold): weak-but-otherwise-usable signals never open the squelch at all — the classic "my coverage seems worse than it used to be" complaint that turns out to be a squelch setting, not an actual RF/antenna/site problem.
- Set too loose (low threshold): the squelch opens on noise, distant co-channel/skip signals, or marginal signals too weak to produce clear audio, producing frequent bursts of noise or "opening and closing" chatter.
CTCSS Squelch (Tone Squelch)
CTCSS continuously superimposes one of roughly 50 low-pitch sub-audible tones (67–254 Hz) on the transmitted signal. The receiving radio's squelch only opens if it detects the specific correct tone — even a strong carrier stays silent if the tone is missing or wrong. See PL Tones, CTCSS & DCS for the full tone table, the reverse-burst/squelch-tail-elimination mechanism at end of transmission, and how this is used practically.
Digital Squelch (DCS/CDCSS)
A digital evolution of the same idea: rather than one continuous tone, DCS sends a continuously repeating digital sub-audible code — a 23-bit word encoded via FSK at 134.4 bits per second. The squelch only opens when a complete, error-free DCS word is detected, giving noticeably better noise immunity than analog CTCSS tones. See PL Tones, CTCSS & DCS for what's actually known (and genuinely unclear) about DCS/DPL's own invention history.
NAC Squelch (P25)
On P25 systems, the equivalent access-control mechanism is the Network Access Code (NAC) rather than CTCSS/DCS — serving the same conceptual purpose (letting a radio filter for only the intended system/traffic) but implemented as part of the P25 digital protocol itself rather than a separate sub-audible tone/code system.
Common Misunderstandings
- "Carrier squelch listens for a specific carrier signature" — as covered above, classic analog squelch is actually a noise-threshold detector, not a carrier-identity detector; it opens for any sufficiently strong signal because it has no way to distinguish one carrier from another — that discrimination is exactly what tone/digital/NAC squelch add on top.
- "Tone/digital/NAC squelch is a security or privacy feature" — it isn't; like the underlying CTCSS/DCS tones themselves, these squelch modes only control whether a radio's speaker automatically unmutes, and provide no actual encryption or protection from anyone with a scanner or a radio set to carrier squelch — see the "Not Encryption or Security" discussion on PL Tones, CTCSS & DCS for the full explanation, which applies equally to squelch mode generally.
- "Squelch type is a single fleet-wide setting" — a radio's transmit (encode) and receive (decode) squelch settings are configured independently, and even different radios within the same fleet can be configured differently — a squelch-related complaint should always confirm what's actually programmed on the specific affected radio(s), not assume it matches "what the rest of the fleet uses."
Related Pages
- PL Tones, CTCSS & DCS
- Reverse Burst and Squelch Tail Elimination
- Comparators
- Common Radio Programming Parameters
- P25 Project 25
- COR and PTT Interfacing
References
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.