Troubleshooting RadioPro Dispatch: Grayed-Out Controllers, Audio and Transmit Errors
Causes and corrective actions when RadioPro Dispatch radio controllers are grayed out, audio is missing or delayed, or the transmit error window appears.
This article collects the troubleshooting steps for RadioPro Dispatch. For general network and gateway connectivity background see troubleshooting-roip-and-gateway-connectivity and network-troubleshooting-commands.
Start in Options, Manage IP Gateways (also called Manage Devices). It shows, for each gateway, whether the gateway is Connected and its firmware version, and whether the radio is connected and its firmware version. The System Problems box at the bottom lists current faults such as unconnected radio resources and license limits.
One Radio Controller is grayed out
A single darkened controller means one of: the network connection between the PC and that IP Gateway is lost ("Can't connect to Gateway"); the gateway is off or rebooting; or the control-station radio is disconnected, off or rebooting ("Radio Disconnected").
Gateway Status is Connected but the radio shows "Radio not connected":
- Check that the control-station radio is powered on.
- Check that it is physically connected to the IP Gateway with the supplied cable.
- Make sure a programming cable is not connected to the radio's front microphone connector. If one is, remove it and reboot the radio.
Gateway Status is Not Connected:
- Check power to the gateway and that the blue Power light on its front is lit.
- Check that the gateway answers a
pingfrom the PC (networking-icmp-and-ping). - Look into the left-side vent holes and watch the red LED: not blinking means the reboot is complete and the gateway is running normally; blinking means it is rebooting, which should finish within 2 minutes. If it does not, the unit should be returned for repair.
- If the console and gateway are on different subnets, check that port forwarding is correct in the firewall or router (port-forwarding-and-remote-access).
- Check the IP address and port listed in Manage IP Gateways, and that the gateway's data activity LED on the Ethernet connector is flashing.
For a MOTOTRBO control station, also confirm that the gateway and the radio are configured for different IP subnets; the system planner shows the address scheme for each system type (radiopro-system-planning-for-mototrbo).
All Radio Controllers are grayed out
Possible causes: power removed from all gateways; the network between the PC and the gateways is lost; the USB hardware key is not installed; the software license that matches the key is not installed; or a temporary license has expired.
- Verify that the gateways have power and answer a ping, and that the ICU utility can see them.
- Remove the USB key and listen for the Windows disconnect tone; re-insert it and listen for the connect tone.
- In Options, Update License, confirm that the USB Key ID matches the serial number engraved on the key and that the number of Connections matches the number of radio controllers.
Audio problems
| Symptom | Possible cause and action |
|---|---|
| Audio from subscribers cannot be heard at the console | The control-station radio is not receiving the subscriber (raise its volume and check the radio system); the radio is not connected to the gateway's DE-9 connector; desk speakers are off or too low (set to about 50%); no audio playback device is in the Audio Presets; Select or Unselect slider too low; the Radio Controller is muted; or the controller's audio driver is corrupt (other controllers still work). To fix the last, in Edit mode remove the faulty address in Manage IP Gateways and add it again. |
| Subscriber audio is delayed by more than a second | Recordings are being written to a slow device such as an external USB drive. Use a second partition, a second internal disk, an external eSATA disk or network storage. |
| Console audio cannot be heard at the subscriber radios | The microphone or headset is not connected, or not configured in the Audio Presets; the gateway is not connected to the control-station radio; or the MOTOTRBO control station is not configured for "Rear PC and Audio". Watch the VU meter while keying. |
See radiopro-dispatch-voice-dispatching for the volume sliders and audio-levels-and-radio-interfacing for background.
The Transmit Error window
This window can appear when PTT is pressed and the microphone chosen for transmit is not connected, for example because it was unplugged or replaced.
- In the Windows system tray, right-click the speaker and choose Recording devices. If the microphone is not listed, connect it. If it is listed, speak and watch the level indicator; it should reach at least 50% at normal voice level.
- In Dispatch, check Options, Audio Presets to be sure the right preset is selected.
- If needed, the administrator opens Edit mode, Options, Audio Presets, Configure, Devices and verifies the Mic In setting for that preset, then saves.
For USB microphones with PTT buttons see radiopro-microphones-and-ptt-accessories.
Source documents
This article summarizes the following published CTI Products manuals. They are the authoritative reference.
See also: CTI product documentation
This article is part of the CTI Products Knowledge Base. Questions about RadioPro or MCN products? Call +1 (513) 595-5900 or email info@ctiproducts.com.
Informational only. This article is general background and is not engineering, safety, legal or regulatory advice. Verify requirements with the equipment manufacturer and the applicable authority before relying on it. Product names and trademarks belong to their respective owners.